Call 01493 277103

Pitched roofing

What Is a Roof Valley?

A valley is the inside corner of a roof, where two slopes share one channel. This page covers how valleys are built, why they leak and what to check before anything is repaired.

Get a written quote

Call 01493 277103WhatsApp us

Crumbling mortar beneath old half-round clay ridge tiles

The short answer

A roof valley is the inside corner where two sloping roof planes meet, forming a channel that carries rain from both slopes down to the gutter. It can be lined in lead or GRP, or formed from valley tiles, and because it gathers the run-off from two slopes it is a point where leaks can start.

Where valleys appear and what they carry

Any roof that turns a corner has a valley. An L-shaped house, a gable that meets a main ridge at right angles, a dormer cheek or an extension tied into an older roof each creates one. The valley is the mirror image of a hip roof corner. At a hip the slopes turn outward and rain parts company, while at a valley they turn inward and rain gathers.

That is the property that matters. Two slopes feed one channel, so a valley carries more water than the same length of ordinary roof, and it carries it along a line instead of letting it spread. The water also arrives at the bottom of the valley in a concentrated stream, where it is delivered into a gutter or onto a lower roof.

Because of that load, a valley is built as a gutter in its own right. It has to be waterproof along its whole length, it must be wide enough for the flow, and the tiles on each side have to be cut neatly to its edges without leaving a gap.

Three ways to build a valley

Valley constructions compared
TypeWhat it isPoint to check
Lead-linedA sheet of lead laid in a boarded channel, with the tiles cut to its edgesSplits, lifted edges, laps that have opened
GRP-linedA moulded glass-fibre channel, fixed and sealed into the valleyCracks, resin that has worn thin, blocked ends
TiledPurpose-made valley tiles that curve through the angle and are laid into the coursesCracked or slipped tiles, gaps at the cuts

An open valley leaves a strip of the lining visible between the tile edges, and a closed or swept valley covers it with tile or slate. Which of these a roof has follows from the way it was built and the covering laid on it.

Lead is the traditional lining. MyJobQuote says that correctly installed lead flashing can last for over 80 years, a figure given for flashing rather than for valleys. Our guide to GRP and lead valleys sets the two linings side by side.

Why valleys leak

A valley fails where its water-carrying job meets the weak point of its material. The common mechanisms are plain enough:

  • Debris and moss collect in the channel, dam the flow and push water sideways under the tile edges.
  • Lead thins or splits where it has flexed with the weather, or where a foot has pressed it.
  • A GRP lining cracks or its surface wears, and sunlight breaks down the resin.
  • Tile edges slip or crack, opening a gap beside the lining.
  • Nails or fixings through the lining leave a hole that was never sealed.

A valley leak can appear inside the house some way from the valley itself, since water under the lining runs along the boards before it drops. A brown mark on a ceiling beneath the line of a valley deserves a look.

Checking from the ground helps up to a point. A valley with a visible build-up of leaves, moss or a tile out of line can be spotted from the road, but a split in lead cannot be seen without getting close.

What the survey checks and how repair is priced

A valley is checked as part of the roof around it. At Total Roofing Great Yarmouth a survey looks along the whole length of the valley, at the lining, the tile cuts, the junction at the ridge and the point where it discharges. It also looks at the timbers beneath, since long-running damp can stain or soften them.

No guide we draw on prices valley work, and the published lead figures, which relate to chimney leadwork, do not apply. Our quote for a valley follows the survey and is one written total.

The repair route depends on the finding. A blocked channel needs clearing, a worn lining needs replacing and a cracked tile needs swapping. Where the lining has failed along its length, a new one is laid, which our page on lead valley replacement describes. For repairs to the area as a whole, see roof valley repairs, and for the covering around it the pitched roofing service.

Questions and answers

What is the difference between a valley and a hip?

A hip is the outward corner, with water parting either side of the line. A valley is the inward corner, with water from both slopes running into a channel. The hip is capped with tiles that face outwards, while the valley is lined to carry the flow, so the two are built and repaired differently. Where a roof has both, the survey takes each in turn, because a defect at one can send water towards the other and leave the second looking at fault when it is not.

Can I clear a valley myself?

Debris can be cleared from a valley that is reachable safely, for instance at a low roof edge from a stable ladder. A valley higher up a slope is a roofer's job, because stepping into the channel can crack lead or GRP and the slope has no rail to catch a fall.

Is a valley the same as a gutter?

Each moves water, though from different positions. A valley carries water across the roof surface and delivers it to a gutter at the eaves, and a gutter sits at the edge and takes it away. A leak at the end of a valley can look like a gutter fault, so both are checked in a survey.

Get a written quote

Tell us about your roof

Hand dressing a lead ridge roll with a wooden bossing stick

10-year workmanship guarantee, in writing

Call WhatsApp Written quote