The short answer
A bonnet hip tile is a shaped hip tile whose lower end flares out over the tiles beside it, like the brim of a bonnet, so each tucks under the next up the slope. They are laid along the hip, and Marley says hip tiles need a mechanical fixing, not mortar alone.
The shape and why it is called a bonnet
Down a hip the two planes of the roof come together on the outside of the corner, and the join needs a cover. The simplest cover is a half-round tile laid like a ridge tile. A bonnet hip tile does the same job with a more finished outline. It is formed with a curved or angular crown, and its lower end is cut or moulded to a flared shape that sits over the tiles on each side.
The comparison with a bonnet is to the flared brim. Seen from below, each tile looks as if it wears a small hood. The tile above overlaps the one below, so the run reads as a series of overlapping caps rather than a plain half-pipe. In clay the tiles are fired to a colour that weathers with the rest of the roof.
A bonnet hip is a decorative detail as well as a weatherproof one, and it belongs on the hip line rather than the ridge. Our page on what a hip roof is explains the line they follow.
Bedding, fixing and the standard
Traditionally bonnet hips were bedded in mortar along the line and held by that bed. Mortar ages and crumbles, and the codes have moved on. Marley explains that the 2015 amendments to BS 5534 made it clear mortar "could no longer be relied upon as the only means of securing the roof covering", and its guidance gives ridge and hip tiles a mechanical fixing in every case, matched to the uplift calculated for the roof.
In practice a bonnet hip is therefore fixed with a metal fixing: a nail or screw through the tile into a batten or hip rafter, or a clip or bracket. Mortar can still bed the tile and seal the joints, but the holding is done by metal. A hip iron at the foot of the hip can support the lowest tile.
BS 8612:2018 is listed as current and sets the specification for systems that are fixed dry along ridges, hips and verges. The data sheet from the maker of a bonnet tile says whether that tile suits a dry system. Installing to BS 5534 is not required by law, Marley notes, and the fixing for each roof follows a specification that allows for how exposed the roof is.
Matching bonnet hips on an older roof
Replacing one is not as simple as buying one. Clay bonnet tiles come in different sizes, curves and colours, and an old tile weathered by decades will not match a new one sitting beside it. Salvage yards, reclaimed stock and a maker's current range are the places to look, and the colour of a new tile can be a shade off until it ages.
The things to match are listed here:
- The length and width of the tile.
- The profile of the crown.
- The shape of the flared end.
- The colour and the texture of the clay.
A tile that is close in all of these will sit properly on the bedding and look right from the road. One that is a little too long or too wide will leave a gap or ride up on its neighbour.
Our page on matching old roof tiles sets out the approach for the whole covering, and the hip is a smaller version of the same task. A single cracked bonnet can sometimes be replaced alone, as the page on replacing one ridge tile explains for the ridge.
Listed homes, the survey and the price
A period house or a thatched cottage may be listed, and a listed home needs listed building consent for work "in any manner which would affect its character as a building of special architectural or historic interest" (the Listed Buildings Act, section 7). Changing a bonnet hip for a plain one, or the reverse, is the sort of change the council should be asked about first. Planning rules apply in conservation areas and the Broads too, and our planning guide explains the route.
At Total Roofing Great Yarmouth a survey follows the hips along their length, including the bedding, the fixings, the hip iron and the tiles beside them. Hip work is priced after the survey, because a ridge price is not a hip price, and the figure comes as one written total. We can look at a WhatsApp photo before the visit.
For the rest of the work on a tiled roof, see the pitched roofing service.


