Call 01493 277103

Lead roofing

Patching Lead on a Roof

A split in lead can sometimes be patched without renewing the flashing. Here is how a lead patch differs from a tape or sealant cover, where a patch suits and where it does not, and what published prices say.

Get a written quote

Call 01493 277103WhatsApp us

A roofer dressing lead flashing round a brick chimney stack

The short answer

A patch suits one short split in lead that is otherwise sound. A patch of lead fused to the sheet is a repair to the metal; tape and sealant only cover the split. A patch cannot cure lead that is cracking at several folds, and no lifespan in years can be promised for one.

What a patch is and what it is for

A lead patch is a small piece of new lead put over a hole or split in an existing sheet, so the water-carrying surface is restored without taking the whole flashing out. It belongs to the family of repairs described on our page about whether to repair or replace lead flashing. The cost of that choice is set out near the end of this page.

It suits a fault with clear edges: a short split at a fold, a hole where a nail or a fixing has worked loose, or a spot worn through where something has rubbed. In each case the surrounding lead is sound, and the patch deals with the one place where water got in. The edges of the patch are dressed so that rain runs over them, never under them.

A patch does not suit lead that is cracking along several folds, lead that has thinned over a wide area, or a flashing that has slid off its joint in the wall. Patching those leaves the cause in place, and a new split can open beside the patch within the same season.

Welded patch, tape and sealant compared

Three kinds of cover get called a patch, and they behave very differently. The comparison below sets out how each one works, and none of the three comes with a life in years.

Three ways of covering a split in lead
MethodWhat it isWhat it does
Lead patch, weldedNew lead fused to the old sheet with a flameMends the metal, and moves with the sheet
Self-adhesive tapeA bitumen or foil strip stuck over the splitCovers the split and relies on the glue
Sealant or masticA flexible bead smeared over the gapHides the split for a spell

Welding, which lead workers also call lead burning, joins lead by melting the edges so they flow together with no separate solder. It makes the patch part of the sheet. Our answer on what lead welding on a roof is explains the process and its fire risk.

How long a patch lasts

A patch has no lifespan in years to quote. The one lifespan statement for lead flashing is MyJobQuote's, that correctly installed lead flashing can last for over 80 years, and that describes a whole flashing, not a patch on one.

What decides how long a patch holds is the lead around it. If the flashing split because it was cut too long or fixed too tightly, the cause is still there, and the sheet will keep moving and cracking close to the patch. If the split came from damage, such as a ladder, a dropped tile or a boot, the patch deals with a one-off fault and the flashing carries on. The patch is only as sound as the sheet it is joined to.

A tape or sealant cover is a different case. Both depend on a bond to the surface, and a bond to a moving, dusty sheet is the weak point. That is the reason for treating them as stopgaps, a view set out on our page about mastic on lead flashing. If a cover has been put on once and the stain returns, the next step is a survey, not a second layer.

What patching costs, and how a patch is decided

Two third-party figures give the scale. MyJobQuote's lead page (22 September 2026) gives around £200 for patching the lead flashing on a chimney and a full replacement at around £570 on average, and both apply to chimney leadwork only. Checkatrade's repair table (June 2026, exclusive of VAT) puts lead flashing repairs at £50 to £70 per metre, and a rate per metre is not a price for a whole flashing.

On our side, the decision comes from handling the lead at the survey. We check whether the sheet around the split is supple, whether the pointing and clips hold, and whether the covering beside it is intact, and you hear what was found, other faults included. You receive one written total price for the work chosen.

If a patch will not do, the lead roofing and leadwork hub covers the larger jobs, from flashings to valleys. A photo of the split sent on WhatsApp gives us something to look at, and the survey then decides between a patch and new lead.

Questions and answers

Is a patch cheaper than replacing a lead flashing?

On MyJobQuote's chimney figures, yes: around £200 for a patch repair against an average of around £570 for full replacement, with the page last updated on 22 September 2026. Those figures cover chimney leadwork only, and the price of your own job is fixed by the survey, which looks at length, access and the state of the lead.

Can lead tape be used instead of a lead patch?

Tape can cover a split for a spell, but it sticks to the surface and does not mend the metal. On a moving, weathered sheet the bond is the weak point. A fused lead patch becomes part of the sheet, while a new flashing deals with the underlying cause of the split.

Should I patch a flashing that has split twice?

Not without finding the cause. A second split near the first suggests the lead is moving too much, is fixed too tightly or has aged badly. A survey looks at the whole flashing and the wall behind it before a patch, a re-fix or new lead is proposed to you.

Get a written quote

Tell us about your roof

Hand dressing a lead ridge roll with a wooden bossing stick

10-year workmanship guarantee, in writing

Call WhatsApp Written quote