The short answer
Headlap is how far the tail of one slate reaches past the head of the slate two courses below it. Cupa's BS 5534 example pairs a 115mm overlap with a 500mm slate at 20 degrees. Too little overlap leaves a path for rain to run in.
What the overlap protects
A slate roof is a stack of thin overlapping plates. Each course covers the joints of the course below it, and each slate also reaches down past the head of the slate beneath that one. That second reach is the headlap. The head of a slate is its top edge, where the nail hole sits, and the tail is the bottom edge you see from the ground.
The headlap does a plain job: it keeps the nail holes and the gaps between slates covered by two layers, not one. Rain that is pushed up a slope by wind, or held between two slates by surface tension, has to travel the length of the overlap before it can reach the underlay and the batten. The longer that distance, the less likely it is to arrive.
Headlap is a measurement taken on the finished roof and fixed when it is set out. It is not something you can adjust afterwards without lifting the slates, which is why it is decided before the first course goes on.
How headlap, gauge and pitch fit together
Gauge is the distance from the tail of one course to the tail of the next, which is also the spacing of the battens. Headlap and gauge are tied to the slate length. Take a 500mm slate with a 115mm headlap: half of the difference between them is the gauge, so (500 minus 115) divided by 2 gives 192.5mm. A longer headlap shrinks the gauge, so a roof needs more battens and more slates to cover the same area.
Pitch pulls the other way. Cupa reports that BS 5534 "also indicates that the minimum roof pitch for natural slate is 20 degrees in the case of a project situated in an area with moderate exposure and with a slate 500mm long and a 115mm overlap". The figures only hold as a set. A shallower slope, or a more exposed site, calls for a bigger overlap.
For contrast, a clay pantile is a different product: Sandtoft's data sheet gives its Old English Pantile a 75 mm headlap and a minimum pitch of 30 degrees. A pantile figure says nothing about a slate roof.
Three numbers that move together
- Slate length sets how much cover each slate can give
- Headlap is taken out of that length by the overlap
- Gauge is what remains, shared between the two courses
- Pitch and exposure decide how big the headlap must be
Why too little overlap lets rain in
On a steep slope water runs straight down the face of the slates and drops off the tails. On a shallow slope it moves slowly, and a gust can drive it uphill under the tail of a slate. If the headlap is short, that water reaches the head of the slate below, then the nail hole, then the batten.
The leak that follows as a stain on the ceiling some way from the cause, because the water follows the underlay and the timber before it drops. Slipped or cracked slates make the problem worse, since each missing piece takes away a layer of the overlap from the course below.
A roof laid with a short overlap may stay dry in a sheltered spot and leak in a different spot on the same house. That is why the headlap is judged against the site's exposure, and not only against the pitch on the drawing.
What we look at on an existing roof
The headlap cannot be read from the ground, so the survey measures a few slates in place and compares the overlap with the slate length and the pitch. We also look along the courses for slipped slates and for nails that have let go, because a slate that has dropped by a few millimetres has lost some of its overlap, and a run of them means a run of weak spots. The loft side is checked as well: daylight at a joint, stained timber and a damp underlay all show where water has been getting past the covering. Our guide to signs of a failing slate roof lists what can be seen from outside.
If a roof is being re-slated, the gauge is set out again from the slate in hand and the pitch of the slopes. See re-slating a roof for how the work runs, and slate hooks against nails for the fixing limits at lower pitches.
At Total Roofing Great Yarmouth you get a single written total price after the roof has been looked over. The slate roofing hub lists the work we cover.


