The short answer
A lead soaker is a small piece of lead folded into an L, laid under each course of tiles or slates where a roof slope runs beside a wall or chimney. One arm sits under the covering, the other turns up the wall. Leadworx lists soakers at code 3.
What a soaker is and where it goes
Where a pitched roof runs alongside a wall, a gable end, a chimney side or a dormer cheek, the covering ends against vertical brickwork. Soakers seal that junction. Each is a rectangle of lead bent into an L: one arm lies flat under a tile or slate, while the other rises against the wall.
One soaker is laid with every course of the covering, so the row of soakers climbs the slope in step with the tiles. Rain running down the wall falls onto the upturned arm, runs onto the lead under the covering and then out onto the face of the tiles below, never into the roof.
Soakers are the hidden part of a stepped junction. The visible stepped flashing, fixed into the wall, laps over their upturned arms. Our guide to types of lead flashing shows the pieces together, and each moves on its own, soakers with the covering and the stepped piece with the wall. Each soaker is also overlapped by the one above it, so water cannot run behind.
Why code 3
Lead is graded by code, and Leadworx, a lead flashing maker, lists code 3 as "Soakers / Light duty". At 1.32 mm and 14.97 kg/m² in its table, code 3 is the thinnest of the grades it lists, from 3 to 8. Weights vary between suppliers, so those figures are Leadworx's own. The thickness matters because lead this thin is easy to dent and tear if it is handled roughly during a repair.
The reason for a light grade is the work the piece does. A soaker is bent along a tight fold, laid flat and covered, and it follows the shape of the tile or slate above it. Thin sheet makes that easy, and the covering shields it from rain and from boots.
Leadworx writes that code 4 has become the standard choice for general flashing work. So on one chimney the soakers might be code 3, the stepped flashing over them code 4, and the cover at a tall wall code 5. Our answer on which lead code for flashings covers how each is chosen, and how the specification sets the code for each detail.
How soakers fail
Because soakers are hidden, their faults show indoors before they show on the roof. Damp on the wall beside a chimney breast, or a stain on a ceiling next to a gable wall, can come from a soaker that has failed. Water can also arrive from a cracked tile above and run down the face of the lead until it finds a gap.
- A soaker that is too short, so water runs around its edge and onto the timber.
- A soaker that has slipped down out of its course, leaving a gap beside the wall.
- Lead that has cracked at its fold, from being bent back more than once.
- A missing soaker, where a course was laid without one or the lead was lost.
- A tile or slate cracked above a soaker, letting water reach the lead from above.
None of these is visible from the ground. Checking a soaker means lifting the covering, which is roof work, so the stepped flashing and the soakers under it are surveyed together, not guessed at from below. Where a cracked tile is the cause, the tile is dealt with as well as the lead.
Replacing soakers
Because a soaker lies beneath the covering, renewing one means lifting the tiles or slates over it. Where the whole run along a wall has failed, the tiles along that edge come off and the full set of soakers is renewed in step with them. The stepped flashing over the top is dressed back into place or replaced at the same time. Where the wall itself is sound and the stepped flashing is not, the soakers underneath can sometimes stay, and the survey decides.
That is why soakers are dealt with at the same moment as a re-cover, since the covering is up already. On a single repair, we survey the junction first and say what we find, including anything else seen on the roof. The written quote comes as one total price.
Soakers sit among the lead jobs on our lead roofing and leadwork hub, and the guide to lead flashing alternatives looks at what other materials can do at a wall. If you suspect a failed soaker, a photo of the stain indoors sent on WhatsApp is a fair start.


