Call 01493 277103

Commercial roofing

What Is TPO Roofing?

TPO is a flexible single-ply sheet whose seams are fused with hot air. This page explains what the name stands for, how a TPO roof is put together, where the material suits and where the details need care.

Get a written quote

Call 01493 277103WhatsApp us

An old brick workshop with a corrugated cement sheet roof and two rooflights

The short answer

TPO stands for thermoplastic polyolefin. It is a single-ply roofing sheet that softens under heat, so its seams can be welded into one continuous skin. It suits large, simple roofs, and the quality of the seams and the details around the edges decides how well any one roof performs.

What the letters stand for

Thermoplastic polyolefin is a plastic that softens when heated and sets again as it cools. That property is the whole reason the material is useful on a roof: two sheets laid edge to edge can be heated along the overlap and pressed together, and the result is a seam that has fused into a single piece of material instead of being glued or taped.

TPO is made in a factory as a flexible membrane, sometimes with a reinforcing scrim running through it, and supplied on rolls. It belongs to the family of single-ply coverings, alongside PVC, which is also a thermoplastic, and EPDM, which is a rubber. Our page on single-ply roofing describes what the family has in common. This one is about the member that is welded.

Different makers sell different TPO products, with different thicknesses, different reinforcement and different rules for laying. The data sheet for the product chosen sets the conditions, and it is the document that matters when a question comes up about fixing, compatibility with an existing surface or the seam width.

How a TPO roof goes on

The sheet is rolled out across the roof in strips with an overlap at each edge, starting from the low point so that each strip sheds water over the one below it. It is held to the building in one of three ways: fixed through the sheet into the deck with fasteners and plates, glued down to the substrate, or laid loose under a layer of ballast. A hot-air welding tool then fuses the overlaps, and the welder runs a probe along the finished seam to test it.

At the edges, the sheet turns up the wall or parapet and is finished at the top with a trim. Pipes, vents and roof lights each need a shaped piece or a cut patch of identical membrane welded round them. Prefabricated corners and collars are made for these places, because folding a flat sheet around a pipe is the weak point of any membrane.

A TPO roof sits on insulation, and the insulation sits on a deck. If an older roof is being covered over, what lies beneath the sheet needs to be sound and dry, and the survey checks it before the work is specified.

Where it suits and where it needs care

A large, simple roof with few penetrations is where a welded sheet shows its strengths. Long straight strips go down quickly, and there are few joints to make by hand. A roof crowded with plant, pipework, roof lights and awkward upstands has more details to turn, and each detail is a place where the seam depends on the welder.

Three questions need answers on an existing building. What is the deck, and will it take fixings? What is under the old covering, and is it compatible with the new sheet? Where does the water go? On that last point, BS 6229:2025 is the standard for continuously supported flexible waterproof coverings, and it sets a minimum finished fall of 1:80, so the survey checks the fall and the outlets before the sheet is chosen. Where ponding already shows on an old roof, that is looked at first, since a new sheet laid over the same hollows would sit in the same water.

A lifespan for a particular TPO product belongs with its maker's data sheet and its conditions. The ranges that are published for other coverings sit on the commercial roof lifespan page, with each source and date.

What a survey of a TPO roof looks at

  • The seams: that each overlap is fused along its whole length, with no lifting edge or open end.
  • The upstands and trims at walls and parapets, where the sheet is held at the top and can pull away.
  • Outlets and gutters, which should be clear and set so that water leaves the roof.
  • Penetrations, with the collar or patch around each one still tight.
  • The surface for punctures, scuffs along walkways and wear where plant is serviced.
  • Any area that holds a pond after rain, which suggests the fall has been lost.

Surveying a TPO roof follows the method used for any other membrane, and our commercial roof surveys guide describes the approach. A commercial sheet roof is priced once that survey is done, and the quote is one written total for the work. We also point out anything else we noticed on the roof while we were surveying it. The commercial roofing hub lists the other coverings in the group.

Questions and answers

Is TPO the same material as PVC?

No. Both are single-ply sheets that can be heat-welded, but they are different polymers, made by different processes and sold under different product names. The two have different data sheets, so the laying rules and the details around a roof are specific to the product rather than to the family.

Can TPO be laid over an old roof?

Sometimes it can, and the survey decides. The old covering has to be sound and dry, the deck has to take the fixings or the adhesive, and the maker's data sheet has to allow the old surface beneath the new sheet. A roof with wet insulation or failed sheets needs to be opened up and put right first.

How is a TPO roof repaired?

A split or a failed seam can be mended by cleaning the area and welding a patch of the same membrane over it, where the sheet around is sound. A repair on old, weathered sheet is harder than one on new, so the survey takes in the sheet surface as well as the leak, and the fixings, trims and any welded patches already on the roof.

Get a written quote

Tell us about your roof

Hand dressing a lead ridge roll with a wooden bossing stick

10-year workmanship guarantee, in writing

Call WhatsApp Written quote