Call 01493 277103

Commercial roofing

What Is Single-Ply Roofing?

Single-ply roofing waterproofs a large flat roof with one factory-made sheet instead of layers built up on site. This page covers how the sheet is joined and held down, what the standard asks for and what the figures say.

Get a written quote

Call 01493 277103WhatsApp us

Rear flat roofs of a brick shop parade with flats above

The short answer

Single-ply roofing is a waterproof covering made from one layer of flexible factory-made sheet, laid in strips across the deck and joined at the seams. PVC, TPO and EPDM are the materials named here. A survey of the deck, the details and the drainage decides which suits a roof.

One sheet instead of many layers

The name describes the build. Where built-up felt stacks several bitumen layers, a single-ply roof relies on one membrane. The sheet is made in a factory to a controlled thickness, delivered on rolls and unrolled across the roof, then joined to the next strip along its edge. The deck beneath it, and the insulation between deck and sheet, are separate parts of the build-up, and the sheet's job is only to keep the rain out of them.

Three materials come up under this heading. PVC and TPO are thermoplastics, which means the sheet softens under heat and can be welded to itself. EPDM is a synthetic rubber, and its seams are bonded with adhesive or tape. Each has its own data sheet from the maker, and the data sheet governs how it is laid and what it can be laid over. The TPO roofing page goes into the second of these.

The common idea is that the roof is waterproof because the sheet is, and that stays true only where the joins, edges and openings are as sound as the sheet itself.

How a sheet is joined and held down

A seam is where a single-ply roof is made or lost. On a thermoplastic sheet a hot-air welder fuses two overlapping strips into one piece along the join. On rubber, the strips are bonded with adhesive or a seam tape. Both methods depend on a clean surface and care in the laying, and a seam that has been done badly can look sound from the ground.

Three methods hold the whole sheet to the building. It may be fixed mechanically through its edge into the deck, bonded to the surface beneath with adhesive, or laid loose and weighted down with ballast such as stone or paving. Each loads the building differently and each wants a different deck, which is one reason the survey reads the structure before a covering is recommended.

At walls, parapets, roof lights, pipes and outlets the sheet is turned up or shaped around the object and finished with a trim or a preformed corner. These details are where a survey spends its time, since a plain field of sheet has no joints to fail except the seams.

Falls, drainage and BS 6229:2025

A single-ply roof is called flat but must still drain. BS 6229:2025 is current and applies to flat roofs, and to curved roofs with a pitch not greater than 10 degrees, that use continuously supported flexible waterproof coverings, which is the category sheet membranes fall into. It replaced BS 6229:2018, which was withdrawn on 16 December 2025.

NFRC's summary of the update says the code sets "a minimum 1:80 finished fall for general roof areas and internal gutters". IKO, a membrane maker, reports that the roof should be designed for 1:40 in order to reach a 1:80 fall once built. One figure is the finished fall and the other is the design target.

A sheet laid on a roof that ponds still keeps water out for a while, but the same patch stays wet and loaded. For that reason the survey checks outlets, gutters and levels before it turns to the condition of the sheet, and it notes any area where the surface holds a puddle after rain.

Lifespan and cost figures

Published EPDM lifespans
ItemFigureSource and date
EPDM lifespan25-30 yearsHomeBuilding, updated 30 September 2025
EPDM lifespantypically lasts 30 to 50 yearsLess, updated 9 November 2026

The EPDM figures above are the only lifespan ranges quoted here for single-ply materials. No range for PVC or TPO appears in them, and a maker's data sheet is where a lifespan claim for a specific product belongs, with the conditions attached to it.,A sheet roof on a unit, shop or warehouse is priced after a survey. Area, access, the deck, the insulation beneath the sheet and the number of outlets and roof lights all move the figure, and what you receive from us is one written total. Because the field of a sheet roof is simple, much of the cost sits in the upstands and penetrations rather than in the sheet.

For the wider picture of coverings, see the guide to commercial flat roofing systems, and for what a survey records on an existing membrane, commercial roof surveys. Our commercial roofing hub lists the rest.

Questions and answers

Is single-ply the same thing as EPDM?

No. EPDM is one single-ply material, a rubber. PVC and TPO are others, and they are thermoplastics that can be heat-welded at the seams. Single-ply describes the build, one layer of membrane, and the material describes what that layer is made of. Each has its own data sheet from the maker.

Is a split single-ply sheet a repair or a replacement?

Either can be right, and the survey decides which. A split, a failed seam or a loose upstand can be mended where the sheet around the damage is sound. A membrane that has hardened, lifted across a wide area or sits over wet insulation is another matter. The survey describes both cases and the quote reflects the result.

Does a single-ply roof need a fall?

Yes. BS 6229:2025 sets a minimum finished fall of 1:80 on a membrane roof. IKO reports that designing for 1:40 is how a builder reaches it. Whichever membrane is on top, a roof that holds standing water has not been left with that fall, and the seams and details take the wear.

Get a written quote

Tell us about your roof

Hand dressing a lead ridge roll with a wooden bossing stick

10-year workmanship guarantee, in writing

Call WhatsApp Written quote