The short answer
It depends on the covering, and no single figure fits every roof. Published ranges start at 10 to 15 years for felt (HomeBuilding) and reach a zinc roof that its maker, VMZinc, says "can last in excess of 100 years". Each range describes a material, not a promise about your roof.
Published lifespans by covering
Two advice sites publish lifespans for the coverings that go on flat and low-pitch commercial roofs. HomeBuilding's table was last updated on 30 September 2025, and the Less website's flat roof guide was updated on 9 November 2026. Where both give a figure for the same covering, the two do not match, so both are shown beside each other.
| Covering | HomeBuilding | Less, or the maker |
|---|---|---|
| Felt | 10-15 years | 10 to 20 years, "depending on quality and installation" (for torch-on felt) |
| EPDM rubber | 25-30 years | typically lasts 30 to 50 years |
| GRP | 25-30 years | 25 to 40 years with minimal maintenance |
| Lead flat roof | 60-100 years | 50 to 100 years |
| Zinc | not listed | VMZinc: can last in excess of 100 years |
Neither site gives a reason for the gap between its figure and the other, and neither describes a particular building. A range is a statement about the material under good conditions. PVC, TPO, profiled steel and fibre cement sheets do not appear in these tables, so none of them is given a figure on this page.
Zinc, lead and the other metals
Zinc and lead are the two metal coverings with published figures. VMZinc, which makes zinc sheet, writes: "When correctly designed and installed a zinc roof can last in excess of 100 years." That is a maker speaking about its own product, and the words "correctly designed and installed" carry as much weight as the number does.
Lead turns up twice, because it serves as a covering and also as flashing at the edges of other roofs. MyJobQuote says correctly installed lead flashing can last for over 80 years, and adds that higher codes can reach over 100. Lead sheet is graded by code from 3 to 8, and the specification sets the code for each detail.
Profiled metal sheeting on a warehouse or industrial unit is a separate material. The sources above give it no lifespan, so this page does not either. What a survey does is read each sheet on the roof being surveyed: the coating, the cut edges, the fixings and the laps between sheets. That reading says more about the remaining life of one particular roof than any table can, and it is the reason a survey comes before a quote.
What shortens or extends a roof's life
The figures above assume a roof that was built well and has been kept clear. These are the conditions a surveyor looks for, because each one changes how long a covering lasts:
- Standing water. BS 6229:2025 sets a minimum finished fall of 1:80 on a membrane flat roof. A roof that holds a pond is not draining to that fall, and the same patch of covering stays wet after every shower.
- Blocked outlets and gutters. A leaf-choked outlet turns a roof into a shallow tank, and the load and the wet both rise.
- Foot traffic. Anyone servicing plant, aerials or air conditioning units walks one route on every visit, and a worn path in the covering records it.
- Penetrations. Every pipe, flue and cable that passes through the roof needs a seal around it that stays tight.
- Wet insulation under the covering, which can sit unseen until the layer above gives way.
None of these is specific to one material. They apply to felt, sheet and metal alike, which is why the survey looks at drainage and details before it looks at the age printed in a table.
Repair, overlay or replace
Age does not settle the question alone. A roof well into its published range may need a patch at one upstand and nothing else, whereas a roof of half that age with a failed outlet detail may need far more. The survey walks the full extent of the roof, including areas away from the leak, and we point out anything else that caught our eye while we were up there. Our commercial roof surveys guide describes the survey itself, including what it looks at and what a report on an older roof needs to cover, and commercial roof maintenance covers what keeping a roof clear involves.
A new commercial covering is priced after a survey, since no cost range for it is sourced, and the size of the roof, the access and the covering chosen all move the figure. What you receive from Total Roofing Great Yarmouth is a single written total. Our commercial roofing hub lists the other guides in this group, from flat roof systems to cladding.


