The short answer
A slate tingle is a narrow strip of lead or copper that is fixed to the batten and folded up over the bottom edge of a repair slate to hold it. A handful on a slope is a normal repair. A slope covered in them suggests the original nails are failing.
What a tingle does on the slope
A slate roof is built from the eaves upward, and every slate is pinned by nails that are then hidden under the course above. That is neat when the roof is new and awkward once one slate has to be replaced, because the nail holes and the nails sit under slates that are still sound. You cannot drive a fresh nail through a covered slate, and lifting a whole slope to reach it would be out of proportion to the fault.
The tingle solves that. It is a strip a few centimetres wide, cut from sheet lead or copper. One end is nailed to the batten in the gap left by the missing slate. The new slate is slid up into place over it, and the free end of the strip is folded up and back over the bottom edge of the slate, which stops it sliding out. The result is a small bright or dull-grey tag at the foot of the slate, visible from the ground on a clear day.
The word is a trade one. Some roofers say clip, strap or tag. They all mean a strip that does the job of the missing nail, and the point of knowing the term is that you can recognise it when it appears in a quote or on a survey sheet.
Lead, copper and what they do to the repair
Lead and copper are chosen because both bend by hand, do not rust, and sit under a slate without cutting into it. Correctly installed lead flashing can last for over 80 years, according to MyJobQuote, which is the nearest sourced life for lead on a roof, though that figure is for flashing and not for a tingle in particular.
Matching the strip to the roof matters because two metals in contact can stain or wear. A bright new copper tag on an old grey slope shows up from the road, while lead weathers to a colour close to the slate itself. Whichever is used, the strip should be wide enough to hold and short enough to hide below the slate above it.
A tingle also leaves the repair slate hanging by one folded point at its tail, with no nails of its own through the head. It is a holding fix. It resists the weight of the slate and a gust lifting it, but it is not a fixing in the way a pair of nails driven through the slate is. That is why it belongs with single-slate repairs, and our guide to slate roof repairs explained sets out where each repair sits.
When a few tingles turn into a warning
Count them by standing back across the road, or by looking from an upstairs window opposite. One or two over fifty years is the sign of a roof that has had a couple of slipped slates replaced. A dozen on one slope, or a line of tags running across a course, says that slates keep slipping in the same area, and the cause is probably in the fixings. Slates that have been replaced several times can differ slightly in thickness, so the slope can look patchy as well as feel loose.
One cause is nail fatigue: the old nails corrode or loosen, and the slates they held slide down, until a tingle or a stub of nail is all that stops them dropping. Swapping slate after slate for tingles deals with the symptom while the cause stays put, so each new tag sits on a slope with more slipped slates still to come. The guide to nail fatigue in slate roofs explains what the fault is and how it spreads.
Signs that tingles are a symptom
- Several tags clustered on one slope
- Slates sitting lower than their neighbours
- A line of slipped slates across one course
- Loose slates that move when pressed from below
- Stains on the ceiling beneath that slope
Tingle, hook or nail: choosing the repair
Some roofers carry both methods on the van, and a tingle is not the only way to fix one slate. A slate hook, a long stainless or copper pin that catches the tail and holds it from below, does the same job without folding anything over the slate. Cupa, a slate supplier, advises that hooks stay off any pitch under 25º, so on a shallower roof a tingle may be the only choice, and the pitch decides it rather than preference.
Where the roof has a sound fixing pattern and only a few slates are gone, either repair holds, and the choice comes down to pitch, access and which looks tidier on that slope. Where the nails are failing across a slope, our guide to re-slating a roof sets out the alternative, stripping the slope and refixing the slates. Our slate roofing hub covers the repair routes side by side. At Total Roofing Great Yarmouth the survey looks over every slope, not merely the gap, and what follows is a written total in one sum.


