Call 01493 277103

Slate roofing

Minimum Pitch for Natural Slate

There is no single minimum pitch for slate, because the figure moves with exposure, slate length and overlap. Here is the published BS 5534 example, what changes it, and what a pitch below it calls for.

Get a written quote

Call 01493 277103WhatsApp us

Roofer washing down a slate roof with a lance from scaffolding

The short answer

Cupa, a slate supplier, reports that BS 5534 gives 20 degrees for natural slate only where exposure is moderate, with a slate 500mm long and an overlap of 115mm. Change any of the three and the figure changes. Hooks are ruled out below 25 degrees.

The published figure and what it assumes

Pitch is how steeply the slope rises, and it decides how quickly rain runs off. Slate lies in overlapping courses, so on a shallow slope rain can be driven or can creep up under the tails, and the covering needs a steeper pitch or a deeper overlap to stay dry.

Cupa gives a worked example in its published answers: BS 5534 "also indicates that the minimum roof pitch for natural slate is 20 degrees in the case of a project situated in an area with moderate exposure and with a slate 500mm long and a 115mm overlap". Each part of that sentence is a condition. The 20 degrees belongs to that exposure, that slate length and that overlap together, and it is not a rule for any roof.

BSI lists BS 5534:2014+A2:2018 as the current edition of its slating and tiling code. Marley, a tile maker, notes that installing to BS 5534 isn't a legal requirement; the code is a recognised standard of practice rather than a statute.

Why exposure, length and overlap move it

Three things work against each other. A longer slate gives a deeper cover for the same overlap, so a longer slate can lie at a lower pitch. The reverse holds as well: a short slate with a small overlap gives little cover and needs a steeper slope to shed rain. A bigger overlap does the same, because water has further to travel before it reaches the nail line. Exposure goes the other way: the more driving rain a site receives, the steeper the pitch or the deeper the overlap has to be.

That makes the pitch a design decision for each roof and not a number to read from a table. Marley says BS 5534 minimums "will always be superseded by the generation of a Fixing Specification, which is site specific and takes into account factors such as" location, one of them being "How exposed is the roof? Local topography".

A house in a sheltered street and a house on an open rise can therefore call for different details even on the same pitch, which is one reason the survey looks at the site and not only at the roof.

Cupa's BS 5534 example

Minimum pitch20 degrees
Exposuremoderate
Slate length500mm
Overlap115mm

Cupa, from its published answers on minimum headlap and fixing of slates (read November 2026). The figures hold only together.

Below 25 degrees: the hook limit

Fixing method adds a second limit. Cupa gives it as "hook fixings should not be used on any pitch below 25º". A hook holds the tail of a slate from beneath, so on a roof between 20 and 25 degrees the slates would have to be nailed, because hooks cannot be used there. Our guide to slate hooks against nails explains the two methods.

For repairs the hook limit still applies on an existing roof, where a tingle may be the choice on a shallow slope. If your slope sits near these numbers, the repair method depends on the pitch, so let it be measured on site and do not guess it. Our guide to slate roof repairs explained shows how each method is used.

A level and a rule held against a rafter, or a pitch finder, gives the angle. A rough figure taken from a photograph is not good enough for a decision about fixings, because two or three degrees can put a roof the wrong side of the limit.

If your roof is shallower than the figure

A roof below 20 degrees is not automatically wrong, since an older roof may carry a larger overlap, a longer slate or a sheltered site that makes it sound. It is also not automatically safe. A shallow slope that leaks may be one that was laid with too little overlap for its exposure, and the cure is a different covering or a different method, not another repair. A pitch measurement, the slate length and the overlap on the existing roof are the three numbers that let that question be answered.

Where a new roof is planned, the pitch, slate length, overlap and fixings are chosen together, and we check with the council which planning or building control route applies, before any work is booked. Our guide to re-slating a roof covers the process. At Total Roofing Great Yarmouth the survey covers all slopes and the roof structure, then gives one written total price, and the slate roofing hub lists the work we do.

Questions and answers

Is 20 degrees always the minimum for slate?

No. Cupa reports 20 degrees as BS 5534's figure for moderate exposure with a 500mm slate and a 115mm overlap. A different exposure, slate length or overlap gives a different minimum, so the figure belongs to one roof's specification and not to slate as a whole, and it should not be quoted as a rule.

Can I put slate on my low-pitched extension roof?

Only if the pitch, the slate size and the overlap suit the site, and a low slope may need a different covering altogether. Check the pitch first. For a new roof or extension, ask the council about planning and building control before work begins, so that the route is clear from the start.

How do I find the pitch of my roof?

A roofer can measure it on site with a level and a rule or with a digital pitch finder. From the ground you can only estimate it, and an estimate is not enough to decide between a hook and a nail fixing, so the angle is taken against a rafter in the loft or on the roof itself.

Get a written quote

Tell us about your roof

Hand dressing a lead ridge roll with a wooden bossing stick

10-year workmanship guarantee, in writing

Call WhatsApp Written quote