Call 01493 277103

Slate roofing

What Batten Size for Slate?

No single batten size suits every slate roof, because the batten has to span the rafters, carry the slates and take the nails. This page covers what sets the size and what to ask for in writing.

Get a written quote

Call 01493 277103WhatsApp us

A lead-lined parapet gutter at the foot of a slate roof

The short answer

The size follows the rafter spacing, the weight of the slate and the fixing, so it is set for each roof and not quoted from a table. Ask for graded, treated timber, written into the specification against BS 5534, the current slating and tiling code.

What the batten does under slate

The batten is the horizontal strip of timber nailed across the rafters. Each course of slates hangs from one, so the batten carries the full weight of the covering and the push of the wind on it. It also sets the gauge, the distance from one course to the next, which fixes the overlap between slates. A batten out of line by a few millimetres shows as a wavy course, and a batten that is too weak sags between rafters and lets the slates open up.

Slate is heavy for its thickness, and a slate roof holds a good deal of material in a small space. The timber under it has to be sound at every point, not only in the middle of a span. That is why battens are one of the items decided with the slate and the rafters together and never picked on their own.

Where an old roof is stripped, the battens are looked at before anything else goes back, because a rotted or rusted-through batten fails quietly and takes a course of slates with it.

Rafter spacing and the load set the size

A batten spans from rafter to rafter. The further apart the rafters, the deeper or stronger the batten has to be to carry the same slates without bending. A batten that bows between rafters lets the slates sit unevenly, and the nails working loose in a flexing batten are one route to nail fatigue.

The slate matters too. A larger, thicker slate weighs more per course, and a heavier covering asks more of the timber beneath it. Swapping the covering for one 15 per cent or more heavier brings Building Regulations approval into it, and before work starts the Planning Portal recommends asking a structural engineer or surveyor, so a change of slate on an old roof is a question for the rafters as well as the battens.

Exposure comes in as well. Marley says a site-specific fixing specification overrides the minimums in BS 5534 and weighs how exposed the roof is. A batten is part of that specification: its size, its fixing back to the rafters and the way it is lapped over the rafter all belong in it.

What the batten size depends on

  • The distance between rafters
  • The weight of the slate chosen
  • The gauge the slates are laid to
  • The site's exposure in the fixing specification

Graded and treated timber

Battens are sold graded, which means sorted by strength, and the grade is stamped on the timber. A reputable supplier sells battens that are also treated against rot and insect attack, because the underside of a slate roof is damp at times. Ask for both, and ask that the battens used are the ones written into the specification and not whatever is on the lorry that day.

Mixed-up bundles are a risk on a roof, since a short length of weak timber sits in a course as well as the strong battens do and nobody sees it once the slates are on. For that reason the battens are checked as they are fixed, with the stamps visible, and each length is nailed into every rafter it crosses.

BSI lists BS 5534:2014+A2:2018 as the current code, and Marley says working to BS 5534 isn't required by law. The code is the yardstick that a specification is measured against, so naming it in a quote tells you what the roof is meant to meet, and its absence tells you something too.

Gauge, and what to look at on an old roof

The gauge follows from the slate and the overlap. Take Cupa's example of a 500mm slate with a 115mm overlap: half the difference gives 192.5mm. The battens must be laid to that figure with care, since each course repeats any error in the one beneath it, and a drifting gauge changes the overlap that the whole roof relies on.

On an existing roof the signs of weak battens are slates that sit proud or out of line, a sagging slope and, from the loft, dark timber and nail tips that have rusted. Our guide to signs of a failing slate roof lists what can be seen, and our re-slating a roof page explains how new battens go in.

At Total Roofing Great Yarmouth the survey takes in the roof structure and ends in one written total price. The slate roofing hub lists the other slate work, from a single repair up to a complete re-slate.

Questions and answers

Can new battens go over the old ones?

It is not good practice. The old battens are on a roof that was cut to its own gauge and carry nail holes and rot, and the new slates need a gauge of their own. Battens are stripped and replaced when a roof is re-slated, so the timber under the new slates is known to be sound.

Do slate battens need to be treated?

Treated timber is the safe choice, since the roof space is damp at times and untreated softwood rots, and a batten that has rotted cannot be seen from outside. Ask for treated, graded battens and ask that the specification says so, then check the stamps on the timber when it is delivered to your house.

Who decides the batten size on my roof?

The roof's specification decides it, written against BS 5534 and the slate chosen, with the rafter spacing and exposure taken into account. We look at the rafters and the old battens during the survey, so the written quote covers what the roof actually needs, and we explain any timber that has to be replaced.

Get a written quote

Tell us about your roof

Hand dressing a lead ridge roll with a wooden bossing stick

10-year workmanship guarantee, in writing

Call WhatsApp Written quote