Call 01493 277103

Roof replacement

Can New Tiles Go Over Old Tiles?

Laying new tiles over old ones looks like a shortcut, but it adds weight, buries the timber and clashes with the batten spacing that the new tile is made for. Below is why the old covering comes off first.

Get a written quote

Call 01493 277103WhatsApp us

Roofers working on the grey tiled roof of a brick detached house

The short answer

No. A second layer piles the whole weight of the new tiles on top of the old, and a new covering at "15 per cent or more" heavier calls for approval. New tiles also need battens set to their own gauge, and the old covering hides the timber beneath.

Weight is the first problem

A roof structure is designed for the load it carries. Tiles are heavy, and one maker's sheet for a clay Old English Pantile gives "Weight as laid 41.6kg per m2" (Sandtoft). A second layer of a similar tile would put that much again on top of the first layer, a far bigger jump than the 15 per cent that already needs attention.

Among the reasons the Planning Portal gives for needing Building Regulations approval is a new covering whose weight takes the roof covering up by "15 per cent or more"; it also advises a word with a structural engineer or surveyor before work starts. Approved Document A uses its own wording, treating it as a significant change when "the loading upon the roof is increased by more than 15%".

  • Portal wording: "15 per cent or more", with advice to consult an engineer or surveyor.
  • Approved Document A wording: "more than 15%".
  • Either way, the question is asked of the new covering against the old before any tile is laid.

The battens set their own gauge

Each tile product is made for a set gauge, which is how far apart its battens sit as you go up the slope. Sandtoft gives its clay Old English Pantile a fixed batten gauge of 290mm and a headlap of 75mm, with a minimum roof pitch of 30°. The tile hangs from the batten, and the headlap is the overlap that keeps water out.

Battens fixed to carry the old tiles were set out for the old tile. They sit at the old tile's gauge, and the same battens cannot hold new tiles at a different one. Laying over the old covering means working from battens that cannot be seen, checked or moved, and a fixed gauge is exactly the figure that cannot be fudged without risking the headlap.

Marley's pitch list shows the same dependence on the product: 15° for its Lincoln clay pantile and 25° for its concrete Anglia. A pitch that suits one tile does not suit another, so the new tile's own data sheet is the place to start, never the old tiles on the roof.

What stays hidden under a second layer

What decides a roof's condition lies below the tiles: timber battens, the underlay, the rafters, lead around chimneys and the flashings at verges. A second layer buries all of it. A rotten batten, a torn underlay or a split rafter has nothing to show for itself until a ceiling stains, and by then there are two layers of tile between you and the repair.

Fixing is an issue too. BS 5534 is a code of practice, not law, but since its 2015 amendments mortar alone is no longer relied on to secure the roof covering, and Marley says tile fixings follow a site-specific fixing specification. New tiles need to be nailed or clipped into sound timber, and a second layer lifts them further from it.

Why the old covering is lifted
What is underneathWhat a second layer hides
BattensRot, split timber, the wrong gauge
UnderlayTears, age, a gap at the eaves
Flashings and leadLifted edges, cracks, tired joints
RaftersDamp, decay, movement

What to do instead of a second layer

When a roof covering is worn out, the route is a full re-roof: the old covering comes off, the timber is checked, and the underlay and battens are replaced where they need it. At Total Roofing Great Yarmouth the survey takes in every junction as well as every slope, and you receive one written total for the roof as it really is, with anything else we noticed set out in simple terms.

If the existing tiles are sound and a matching look matters, reusing them on new battens and underlay is a different job from overlaying, because the timber is exposed. That choice depends on the condition of the tiles, which a survey judges. Cracked, flaking or porous tiles do not earn a second life on a new roof, and a few spares in the loft or garage can make up the numbers where the roof has a few broken ones.

Read changing to a heavier roof covering for the weight rules, or choosing a new roof covering to compare options. Both belong to roof replacement.

Questions and answers

Is covering over old tiles cheaper than stripping?

The lower labour is cancelled by what it hides and what it adds, since the old layer stays on the roof, the timber is never checked and the extra weight needs approval or a structural opinion. Published guides price a whole new roof, not a second layer, so only a survey of your roof gives a fair figure.

What if the old roof is asbestos cement?

Then it is not a tile job. HSE says "If the building was built or refurbished before 2000, assume that there is asbestos in it", and calls AC roofs "always fragile". Cement sheets removed whole without breaking them up are non-licensed work, but broken-up sheets are a different category, so ask before anyone walks on it.

Can slates go over old tiles?

A different covering raises the same questions: weight against the old, a batten gauge to suit the new product and the hidden timber. Each slate maker publishes its own limits for pitch and fixings. A new covering needs its pitch, headlap and fixings checked on the product sheet before anything is ordered, and the roof itself has to be measured against those figures, not judged by eye from the ground. A slate roof also has its own batten spacing, so the old timber cannot simply be reused.

Get a written quote

Tell us about your roof

Hand dressing a lead ridge roll with a wooden bossing stick

10-year workmanship guarantee, in writing

Call WhatsApp Written quote