Call 01493 277103

Pitched roofing

Do Roof Tiles Need Clips?

Whether a tile needs a clip, a nail or both is set for each roof by a fixing specification. Read on for how the standard treats fixings, what clips do and where a survey looks for gaps.

Get a written quote

Call 01493 277103WhatsApp us

Cracked mortar bedding under a clay ridge tile

The short answer

Yes, wherever the roof's fixing specification calls for them. Under BS 5534 that specification is drawn up per site and weighs how exposed that site is, so some tiles are clipped and nailed while others are nailed alone. Since the 2015 amendments, Marley says, mortar cannot be the only fixing.

What a tile clip does

A tile sits on its battens under its own weight, but weight is not what a storm tests. Wind passing over a roof pulls upwards on the covering, and a tile that is only resting can lift, rattle, slide or leave the roof altogether. Fixings exist to stop that.

A nail goes through a hole in the tile into the batten. A clip is a small metal or plastic fixing that hooks over a tile edge and nails or screws down to the batten, so it holds the tile without needing a hole in it. Many tile designs are made to be nailed, clipped or both, and the maker's instructions say which.

On a pantile or an interlocking concrete tile the clip also keeps a long run of tiles in line when the roof flexes in a blow. Clips are small and cheap, and a missing one is hard to spot from the pavement. A slipped tile, a tile that rattles or a gap along one course can all point to a fixing that has failed or was never fitted.

What BS 5534 says, and what it leaves open

BS 5534:2014+A2:2018, which covers tiling and slating, is listed as current. Marley's guidance on it makes two points that are worth keeping apart.

The first is about status. Marley says installing to BS 5534 "isn't required by law", which makes it a code of practice rather than a statute. The second is about mortar. The 2015 amendments, Marley explains, mean that mortar "could no longer be relied upon as the only means of securing the roof covering".

Where the standard sets minimums, a specification drawn up for the site in question takes over from them. Marley lists location among the inputs, meaning how exposed the roof is and the lie of the land around it, and designers looking at wind loading on a covering are pointed to the standard.

So there is no blanket rule such as one clip on every tile. The tile type, the site's exposure and the pitch combine to give the specification for each roof, and the data sheet for the tile gives the maker's side of it. The page on BS 5534 and tile fixing goes further into the standard.

Ridge, hip and verge: where the wind pulls hardest

The firmest wording applies to the tiles along the edges and the top of a roof. Marley's advice is that every ridge or hip tile is fixed by mechanical means, sized to the uplift calculated for that roof. Mechanically fixed means held by something other than mortar: a clip, a screw, a strap or a dry-fixed system.

These tiles meet the wind with nothing above them for shelter. BS 8612:2018 is listed as current and covers systems that are fixed dry along the ridge, hips and verges, so a system built to it is one route to a mechanical fixing for them. The page on what a dry verge is shows how that looks at a gable.

On a roof finished with mortar and nothing else, a survey checks the bedding and whether any fixing sits behind it. From below, the visible signals are:

  • Mortar that has crumbled or dropped out along the ridge.
  • A ridge or hip tile that rocks when it is touched.
  • A ridge line that has slumped or twisted.
  • A tile that has slipped out of line with its course.

What we look at and what it costs

Fixings are one more part to examine, alongside battens, underlay and the tiles themselves, and each is judged by what it does for the roof as a whole. A photo sent on WhatsApp shows what is visible from where it was taken, and a survey on the roof shows what is behind it.

Tile clips are not priced by themselves in any guide we draw on, so the only published figures belong to neighbouring jobs. Which? Trusted Traders give £75 to £400 for swapping up to six cracked or absent standard tiles and £80 to £300 for a new ridge tile, both excluding VAT (November 2025). Neither range covers refixing a whole roof, which depends on the area, the tile and the access.

At Total Roofing Great Yarmouth the price for work to your roof is one written total, fixed once the roof has been seen. The wider pitched roofing service sets out the other jobs on a tiled roof.

Questions and answers

Is clipping tiles a legal requirement?

Marley says installing to BS 5534 "isn't required by law". The standard is still the reference that designers consult for wind loading on a covering, and the fixing choices follow from it whether or not the law names it. A re-roof also touches Building Regulations, so the council's building control team is the body that can confirm what applies at your address.

How can I tell whether my tiles have clips?

From the ground you cannot, because a clip sits under or beside the tile edge. Signs that fixings may be missing are a slipped tile, a gap along a course or a rattle in wind. You can send a photo of any of these on WhatsApp to 07880 284133, and we will say what the roof visit would cover.

Do ridge tiles need clips as well as mortar?

In Marley's guidance every ridge or hip tile gets a mechanical fixing, and mortar by itself no longer secures a covering. A dry-fixed ridge system is one way to meet that, and a clip or screw added beside the mortar is another. The fixing specification for the roof decides between them.

Get a written quote

Tell us about your roof

Hand dressing a lead ridge roll with a wooden bossing stick

10-year workmanship guarantee, in writing

Call WhatsApp Written quote