Call 01493 277103

Flat roofing

Torch-On Felt Roofing

Torch-on felt is a layered bitumen roof, bonded together by a gas flame that melts the underside of each sheet. This guide covers the layers, the cap sheet, care with flame work on an occupied home, published lifespans and how repairs are made.

Get a written quote

Call 01493 277103WhatsApp us

Kitchen-diner lit by a large flat rooflight in the ceiling

What torch-on felt is

Torch-on felt is a flat roof covering made of reinforced bitumen sheets. Each sheet is a polyester or glass-fibre core coated on both sides with bitumen that has been modified to stay flexible. The sheets come on rolls, and they are bonded to the roof by heating the underside with a gas torch until the bitumen melts and sticks.

It is the modern descendant of built-up roofing felt, which was laid with hot bitumen from a boiler. The torch replaced the boiler, and the modified bitumen and the polyester core replaced the older, more brittle felt. The result is a covering that is still layered, still bonded to the roof and still laid on garages, extensions and outbuildings.

Because the layers are bonded to each other and to the roof, there are no loose sheets to flap, and a good installation is a single waterproof skin. Its joints and edges need care, because bitumen hardens with age and a seam or upstand that was not properly bonded will open when the roof moves. The sections below explain how the layers are built up and how a roof lasts or fails.

A felt roof is easy to recognise from the ground. The cap sheet has a grainy mineral surface in grey, green or black, the edges end in a drip trim and the roof is nearly flat. From a window above, the laps between sheets show as faint lines, and ponds show as dark or stained patches. Those clues help the survey, but the layers underneath can only be judged up close.

Layers: base, cap sheet and the details

A torch-on roof is built in two or three layers. The first is a base layer, sometimes called an underlay or a vapour layer, laid over the deck or the insulation. It may be bonded or mechanically fixed, depending on what is underneath. It gives a firm sheet to bond the next layer to and adds a second line of defence against water.

The cap sheet goes on top. It is the weather surface of the roof, and it has a mineral finish, such as small stone chippings or slate-like granules, bonded into the top face. This finish protects the bitumen beneath it from sunlight and from foot traffic, and it can be had in a few colours. The cap sheet is laid so that its joints are staggered against those of the layer below and overlap by a set margin.

At the walls, the sheets turn up as upstands, and the top of each is protected by a flashing or a cover strip. At the edge, a drip trim carries water into the gutter. Around outlets and pipes, shaped pieces are bonded in. Our guide to flat roof edge trims covers the edge, and the flat roof replacement guide covers the stages from the deck up.

Torch-on felt terms

  • Base layerFirst sheet, laid over the deck or insulation
  • Cap sheetTop sheet with a mineral weather surface
  • LapOverlap where one sheet meets the next
  • UpstandFelt turned up a wall
  • Drip trimEdge profile that throws water into the gutter

Flame work on an occupied home

Gas flame next to a house is the main difference between torch-on and other flat roof coverings, and it deserves thought. The torch heats bitumen to the point where it melts, and the flame can reach timber, fascias, soffits and the roof edge. A roof laid beside a thatched or timber-clad building, or over a loft with stored belongings, needs more care than a detached garage.

The risk is real because heat travels. Flame at a roof edge can ignite a timber fascia, and heat at an upstand can pass through brickwork into a void. Good practice is to keep the flame away from timber, to use heat shields at vulnerable edges and to check for smouldering at the end of the work. Whether torch-on is the right choice for a given roof is settled at the survey, where the edges, voids and neighbouring buildings can be seen.

Alternatives exist for roofs where an open flame is not wanted. Some felt systems are self-adhesive or bonded with cold adhesive, and other coverings, such as EPDM or GRP, are laid with no gas torch at all. Our guides to EPDM rubber roofing and GRP fibreglass roofing explain those options. An occupied home is a reason to look at all of them before choosing.

Telling the household what is planned helps too. Windows can be shut and cars or furniture moved from beside the work, and anyone at home should know that flame work is happening on the roof overhead.

Points to raise at the survey

  • Timber fascias, soffits or cladding at the roof edge
  • Thatch, boarding or loft contents near the roof
  • Flues, vents and pipes passing through the roof
  • Gas bottle position and access to the roof
  • Whether a cold-applied system would suit better

Felt lifespans, from HomeBuilding and Less

Published lifespans for felt are shorter than for rubber or fibreglass, and the two published figures do not agree. HomeBuilding gives an approximate lifespan of 10-15 years. Less says "Torch-on felt lasts 10 to 20 years depending on quality and installation". The range overlaps without matching.

The Less wording points to the factors that matter, which are the quality of the felt and the quality of the install. A cap sheet bonded to a sound base layer over a dry, flat deck can do better than a thinner product laid quickly. A poorly lapped seam, an unbonded upstand or a base layer laid over a damp deck shortens the life of the roof, whatever the grade of the felt.

Age shows in the cap sheet. The mineral finish wears and the bitumen beneath hardens, cracks and blisters. Ponds develop in low areas and algae shows where water lingers. When the cover starts to craze across the whole surface, patching stops being a sound answer. Our flat roof repairs guide sets out how to choose between patching, overlay and replacement.

It helps to read the lifespan figures alongside the roof's history. A felt roof that has already had several patches and shows crazing across the whole surface is likely to be at the older end of its range, or past it. A roof laid more recently, with sound laps and a dry deck, has more life left in it.

Published felt lifespans

HomeBuilding, approximate lifespan10-15 years
Less, torch-on felt10 to 20 years

HomeBuilding last updated 30 September 2025. Less page updated 9 November 2026, which adds "depending on quality and installation". Both describe the material, not a particular roof.

Repairs and overlays on a felt roof

A felt repair starts with finding out why it failed. A split along a seam is cleaned, dried and patched with a bonded piece of cap sheet that overlaps the damage generously. A blister is cut, dried and re-bonded under a patch. A lifted upstand is stuck down again with its flashing refixed, and a perished edge is cut back to sound felt.

If water has been in for a while, the deck and insulation underneath can be wet, and bonding a patch over damp layers seals the moisture in. The survey checks for that before anything is bonded down. Where the felt is dry and bonded and the deck is firm, a new layer can be laid over the top. Our guide to overlaying a felt flat roof explains when that holds up and when it does not.

An overlay adds a layer of weight and keeps what is below. It suits a roof with a sound deck and dry layers, and it does not suit one with ponds, damp or wide cracking. A strip-back to the deck is the better choice when the layers beneath are suspect, because the new felt then has a clean base.

Where the roof is small, such as a porch or a bay, the work of an overlay or a strip is modest, and where it is large the differences in cost between the options grow. Quote requests should say which roof is meant, because a house can have several flat roofs of different ages.

The price of a felt roof

The figure moves with the roof's area, the number of layers, the deck repairs, the insulation, the trims and the access. Which? Trusted Traders put a felt roof on a single garage at £1,400 to £3,500, in a survey gathered in November 2025, with prices that include labour and materials and exclude VAT. The same guide describes a single garage as 6m x 3m.

Felt has historically been the lower-priced covering, and a lower price can be a fair reason to choose it. The shorter published lifespan figures are worth setting against that, because a felt roof may need relaying sooner than a rubber one. That is a matter for the survey and the written quote, which is one total price.

Where the eaves are out of reach, scaffold sits inside the written quote. A scaffold that takes in the footway needs a licence, and we arrange the licence with our scaffolder. See our flat roofing hub for the other coverings, and the guide to flat roof costs for the published figures.

A single flat roof on a house is not always the only one. A garage, a porch and an extension can have separate coverings of different ages, and the survey prices each as part of the one written total.

Choosing felt over other coverings

Felt is one of three flat roof coverings compared here, alongside EPDM rubber and GRP fibreglass. Each has a published lifespan, a way of failing and a set of details to get right. Felt is layered and bonded, rubber is a flexible sheet and fibreglass is a rigid shell. Choosing between them is a matter of the roof, the budget and the building, and a quote for one covering is worth comparing with a quote for another.

Felt suits a roof where a layered covering is wanted and the budget is a factor. Its shorter lifespan figures are the price of that, and a roof expected to last 10 to 20 years may be laid again within the time that a rubber roof would still be going. Rubber suits simple shapes and buildings that move a little. Fibreglass suits awkward shapes and firm decks.

Beyond the covering, the build-up underneath matters. Whether the insulation sits above the deck or between the joists changes how the roof behaves, and our warm and cold roof guide explains the difference. The survey ties it together and gives one written total price for the roof you actually have, with the covering, the deck work and the trims all inside that one figure.

Layered felt or single sheet

Torch-on felt

  • Layered bitumen sheets
  • Bonded with a gas flame
  • Mineral cap sheet on top
  • Lifespan figures shorter

EPDM

  • Single rubber sheet
  • Bonded with adhesive
  • No flame needed
  • Lifespan figures longer

Questions and answers

How long does torch-on felt last?

HomeBuilding gives an approximate lifespan of 10-15 years, and Less says "Torch-on felt lasts 10 to 20 years depending on quality and installation". The two sources overlap but do not agree. Both describe the material in general, and a given roof depends on its deck, its layers and its detailing.

Is it safe to use a torch on a roof of an occupied home?

It can be done with care, because the flame can reach timber edges, soffits and voids, and heat can pass through brickwork. The survey looks at those points, and where an open flame is not wanted, a cold-applied felt, EPDM or GRP can be considered. Raise any concerns about your roof's edges before work starts.

What is the cap sheet on a felt roof?

It is the top layer, the one that meets the weather. It has a mineral finish bonded into the bitumen, which protects it from sunlight and foot traffic. Under it sit one or two earlier layers, and the cap sheet's joints are staggered against theirs so there is no straight path through for water.

Can a new felt layer go over an old felt roof?

In some cases, where the old layers are dry, bonded and sound and the deck below is firm. Wet insulation, ponds and wide cracking point to stripping back instead. The survey decides, because an overlay over a failing roof only delays the problem and adds weight to the deck, and new felt bonded to a failing base can fail with it.

Get a written quote

Tell us about your roof

Hand dressing a lead ridge roll with a wooden bossing stick

10-year workmanship guarantee, in writing

Call WhatsApp Written quote