Call 01493 277103

Commercial roofing

Insulated Composite Roof Panels

An insulated roof panel is covering, insulation and lining in one factory-made sheet. That changes how it is fixed, how it fails and which parts of it can be repaired, so here is the difference from a built-up roof.

Get a written quote

Call 01493 277103WhatsApp us

Rear flat roofs of a brick shop parade with flats above

The short answer

An insulated composite roof panel is a sandwich of two metal skins around an insulating core, fixed as a single sheet. A built-up roof assembles liner, insulation and outer sheet on site in separate layers. Panels are fast to fit, and their joints, fixings and cut edges are where trouble starts.

Panel or built-up: two ways to build the same roof

A composite panel arrives as one unit. A steel or aluminium skin on the outside, a skin on the inside and a bonded layer of insulation between them make a sheet that is the covering, the insulation and the ceiling lining at once. The panels lap or interlock along their sides, are fixed through the outer skin to the purlins and are sealed at the joints.

A built-up system is assembled in layers on the roof. A liner sheet goes on first, then spacers or rails, then insulation laid between them and finally the outer sheet fixed through the lot. The layers are separate, so a fault in one does not mean replacing the others. A liner can be dried and re-sealed, insulation lifted and replaced, and the outer sheet changed without touching the lining below.

Both are used on industrial units, warehouses, workshops and farm buildings. Neither is better in the abstract. The choice turns on the span, the weight the structure can carry, how the building is used underneath and whatever the roof you already have turns out to need.

Where a panel roof goes wrong

  • Side joints and end laps where the seal has opened, letting damp into the core.
  • Fixings that have worked loose, lost their washers or pulled through the skin.
  • Cut edges at rooflights, flues and trimmed ends, where the coating stops and rust can start. Our cut-edge corrosion page covers that.
  • Dents or punctures that open the outer skin down to the core.
  • Gutter junctions, where a panel meets a box gutter or an upstand.

A bonded core cannot be dried out like a loose layer. Once water has got into it, the insulation can hold damp against the inner skin and the steel. That is why a stain on a ceiling lining below can mean the damage is a good way from the visible mark, and why a survey follows the water back to where it entered.

Condensation is a separate matter. A sealed panel with a failed vapour seal at a joint can let warm air from inside reach cold metal, and the drips look like a leak from above.

Repair, re-seal or replace

Small faults can be repaired in place. A joint can be re-sealed, a fixing replaced with a new one and washer, a small dent in a skin sealed and coated. The sound panels around a fault stay where they are.

A damaged core is another matter. If the insulation behind a split skin is wet or crushed, sealing the surface hides the problem without curing it, and the panel is replaced. If panel after panel has failed at its joints, replacing the roof's outer layer or covering it with a new system is worth pricing against a long run of repairs.

Any new layer adds load. Approved Document A treats a roof load increased by more than 15% as a significant change, so the survey checks what the structure can carry before a heavier covering is specified, and our page on industrial roof cladding covers sheeting options in more detail.

Where panels sit over an old asbestos cement roof, the over-cladding asbestos roofs page explains how a new covering can go above the sheets.

Energy rules, fire and our survey

Insulation levels for a building that is not a home are not the dwelling figures in Approved Document L Volume 1. Which energy rules and which fire requirements apply to a replacement panel on a business building is a question for the council's building control team or a registered building control approver, and the answer can change what is specified. Your insurer may also have a view on the core.

At Total Roofing Great Yarmouth the first step is a look at the entire roof: panels, joints, fixings, gutters and rooflights treated as one structure. Whatever else it shows beyond the fault you rang about is reported to you plainly. A single total in writing then covers the job. Business roofs carry no rate card here, because panel size, access and the extent of damage all change the work, and the price is set after that survey.

The wider range of roofing for business buildings, surveys included, is gathered under commercial roofing. Send a photo on WhatsApp of the panel joint, fixing or stain that worries you and it shows us where the survey should start.

Questions and answers

Can wet insulation inside a panel be dried out?

Not reliably. The core is bonded between two skins, so a damp core cannot be lifted out and dried as a loose layer can. A panel with a wet core can need replacing, and the survey decides it case by case, and a sealed surface repair does not cure insulation that stays wet underneath.

Will new panels need building control approval?

That depends on the extent of the work and the type of building, so ask the council's building control team or a registered building control approver before you order. The energy rules for a business building are not the dwelling figures in Approved Document L Volume 1, and weight and fire performance can come into the question.

Can I cover old sheets with insulated panels?

It can be done where the structure and the old covering allow it, with the extra load checked first. If the old sheets are asbestos cement, the method changes and needs advice before anyone starts. The survey establishes which case applies, and the price follows in writing as one total.

Get a written quote

Tell us about your roof

Hand dressing a lead ridge roll with a wooden bossing stick

10-year workmanship guarantee, in writing

Call WhatsApp Written quote