Call 01493 277103

Skylights & roof windows

Replacing a Velux-Type Roof Window

Velux is the name people search for, but the swap works the same for any make of roof window. This guide covers a like-for-like replacement in the existing opening: sizing, the flashing kit, the regulation figures, blinds and the point where a swap turns into a bigger job.

Get a written quote

Call 01493 277103WhatsApp us

An old brick workshop with a corrugated cement sheet roof and two rooflights

A brand name and a general job

Velux is the brand name homeowners type into a search box when a roof window fails, in the way people say hoover for a vacuum cleaner. Several makers produce roof windows with the same basic parts: a frame fixed to the rafters, a sash that opens or pivots, glazing, and a flashing kit that seals the frame into the covering of the roof. The job described here, taking one out and fitting another in the same place, is the same whichever name is on the old frame.

That matters when you plan the work. A replacement does not have to be the same make as the old window, though the size and the opening style have to suit the hole that already exists. Some people stay with one maker so that existing blinds or controls still fit. Others change make because a window has been discontinued or because a different model is a better match for the pitch of the roof. The size and opening style of the replacement are what matter, whatever the badge.

A swap is the straightforward end of roof window work. The opening is already framed through the rafters, the battens around it have already been cut, and the room below already has a lining that can be sealed to the new frame, so the work stays small and tidy in scale. MyJobQuote's roof window page says a replacement "costs around £100 less for a straightforward swap, as the opening is already in place". The guide to what a roof window costs covers what moves a price in either direction.

Getting the size right

Everything about a swap depends on the size of the existing frame. Too small and the new window leaves a gap that has to be filled with timber and sealed again; too large and the rafters or the battens must be cut, which turns a swap into a new opening. Roof windows come in a range of fixed widths and lengths, so the aim is to find the model whose outer frame matches what is there.

A label on the frame or the sash can carry the maker's size code, and a paper record from the original fitting may still exist. If the label has been painted over or has worn away, the frame is measured instead, from the outside edges of the sash and the frame, and compared with the maker's size list. The measurements are taken at the roof, not from the room, because the lining hides the true frame.

The window's opening style needs checking against the room. A top-hung window that opens outward near a stair or a bed is a different experience from a centre-pivot window that turns inside the line of the roof. A like-for-like replacement keeps the same arrangement, and any change to it is worth deciding before the order goes in, since sashes are not interchangeable between styles. A pivot model swings its lower half into the room, which limits what can stand directly beneath it.

Matching a replacement to the old window

  1. Read any size label on the frame or sash.
  2. Measure the outer frame at the roof, not from inside.
  3. Note the opening style and which way it swings.
  4. Check the covering for the right flashing kit.
  5. Look at the timber round the frame for damp or rot.

The flashing kit comes out with the window

The flashing kit is a set of metal pieces sealing the frame to the roof covering: a sill piece below, side pieces that overlap the tiles or slates, and a head piece above. It ages along with the window, and the seals, the soakers and the underlay collar behind it are part of the same system. A new window fitted into an old kit invites a leak at the oldest joint.

For that reason a replacement uses a new kit made for the covering on the roof. Each kit is shaped for a particular tile or slate profile, so a plain-tile kit and a pantile kit are not interchangeable, and the covering is identified before anything is ordered. If the roof has been re-covered since the old window went in, the old kit may not even suit the covering it now sits in.

Once the old sash and frame are out, the timber round the opening is looked at. A window that leaked for a long time can leave soft or stained battens and rafter ends, and it is better to find that with the window out than after the new one is in. The underlay is lapped round the frame and the new kit is built up from the sill, each piece overlapping the one below, so that rain runs down and off the roof. A longer account of that order of work is in the guide to how a roof window is installed.

The regulation figures for a replacement

A replacement roof window has to meet a standard for heat loss. Approved Document L 2021, in its Table 4.2, sets "1.4 or Window Energy Rating Band B minimum" for windows, with a note that the line includes roof windows. A rooflight, the fixed kind that sits on a flat roof, has its own figure of 2.2 W/m²K. A window that falls short of its figure is a poor choice for a replacement, whatever its price.

For a house, a roof window in an existing roof is normally covered by permitted development. The government's technical guidance says Class C "covers other alterations to roofs such as re-roofing or the installation of roof lights/windows." One condition applies to side slopes. A window located on a roof slope forming a side elevation of the dwellinghouse must be obscure-glazed, and non-opening unless the parts of the window which can be opened are more than 1.7 metres above the floor of the room in which the window is installed. An older window already in the slope is a separate matter from the new one going in.

A listing or an Article 4 direction can change the answer for a particular address (a conservation area or the Broads does not remove Class C by itself), and a listed home needs listed building consent for works that would affect its special architectural or historic character. The planning permission guide for roof work takes those cases one at a time, and the building regulations guide for roof windows covers the energy and escape rules. We check the route with the council first, or with the Broads Authority where the address falls inside its patch, and only then book the work.

When a swap stops being straightforward

A swap becomes a bigger job when the new window is a different size from the old one. A wider window may need a rafter cut and a header fitted; a longer one may need the batten layout changed. At that point the work has the same structure as a new opening, with the same regulation questions, even though a window was already there.

Rotten timber is the other change, and it is a matter of what the wood is like once the old frame is out. If the survey or the strip-out shows soft battens or rafters round the frame, the damaged wood has to be repaired or replaced before a window can be fitted in it. That is the reason a price for a swap is firm only once the roof has been seen, and why the written quote follows a survey.

A third case is the room below. A damp-stained lining, mould around the head of the window, or a plasterboard shaft that has dropped away from the frame tells you the old window leaked for some time. The lining is likely to need repair, and the insulation behind it may be wet. A window replacement that leaves a wet lining in place has fixed the roof and not the room. It is also a prompt to look at the roof round the window, the lead on a nearby chimney and the gutter at the eaves, and the survey takes those in too.

Signs a swap has become a bigger job

  • The new window is a different size from the old one
  • Soft or stained timber round the frame
  • A lining that has dropped or is stained
  • A kit that no longer suits the covering
  • Rafters that are cut or out of line

Blinds, controls and the finish

Blinds for a roof window are made to fit a particular frame, so they are chosen with the window and not retrofitted from a different size. A blind fitted to a Velux-type window may not suit another maker's frame, which is one reason some owners keep the same make. Where a window already has an electric opener or a solar-powered one, the control and its power supply have to be considered when the sash is changed.

Inside, the lining and the plaster round the opening are made good once the new frame is in. If the old lining stays, the frame is sealed to it; if it is rebuilt, the shaft is formed again and decorated. A swap need not mean redecorating the whole room, though a stained lining is repaired before the new window is closed up.

Colour and finish are the last choices. Frames are made in white, in dark finishes and in coatings meant for damp rooms, and the lining can match the ceiling or the wall it sits in. For a bathroom or kitchen window, a finish made for damp air is worth asking about, because condensation can collect at the sill of a roof window, and a surface that can be wiped clean will stay in better shape.

Cleaning and care matter for the finished window. Roof glass can be reached from inside on a pivot model, and a seal left dirty or a drip channel blocked with debris can let water in over time, so a look at both whenever you clean the glass is worth the minute. The guide to skylights and roof windows collects the related guides, and a window that is already leaking gets its own treatment in our leaking roof windows guide.

Questions and answers

Can I replace a Velux window with a different make?

Yes, as long as the new window suits the existing opening in size and opening style, and a flashing kit is made for your covering. Some owners stay with one maker so that blinds still fit; the opening may also be an odd size that only one range suits, but no rule says the make has to match. The fit, not the badge, decides it.

Does a replacement roof window require a new flashing kit?

A new kit made for your roof covering goes in with the new window. Reusing the old one puts a new frame into the oldest, most worn seal on the roof, and the covering may have changed since the first window was fitted, so the kit is matched again at the survey.

How do I know what size of window I have?

Look for a size code on a label on the frame or sash. If it is missing, the frame is measured at the roof and compared with the maker's size list. A photo of the window sent to WhatsApp on 07880 284133 gets looked at on our side as an early view, before a survey visit is fixed.

Is a like-for-like roof window swap cheaper than a new one?

MyJobQuote says, on a page dated 22 September 2026, that a replacement costs around £100 less for a straightforward swap, as the opening is already there. A swap that finds rotten timber, or moves to a different window size, stops being straightforward, and the survey is the stage at which that gets decided; the written price follows it.

Get a written quote

Tell us about your roof

Hand dressing a lead ridge roll with a wooden bossing stick

10-year workmanship guarantee, in writing

Call WhatsApp Written quote