The short answer
Batten gauge is the spacing from one roof batten to the next, measured up the slope. The tile or slate maker sets it on the product sheet, and it works together with headlap and pitch. One example is the clay Old English Pantile from Sandtoft, whose fixed gauge is 290mm.
Gauge, headlap and pitch in plain terms
Three numbers describe how a tiled roof is laid out, and they are easy to confuse. Gauge is the step between battens as they climb the slope. Headlap is the overlap between neighbouring rows of tiles. Pitch is the slope's angle to the horizontal.
The first two are tied together. Fix the battens closer and each tile overlaps the one beneath it more; spread them wider and the overlap shrinks. That overlap is what keeps rain from being driven up under a tile, so a gauge that drifts from the maker's figure quietly weakens the roof, even if every tile is in place and looks neat from the street.
The error cannot be seen from the ground. It can come to light as a damp patch after a spell of hard rain, when the roof has long since been paid for, which is why the spacing is set from the sheet before the first tile is laid.
- Gauge: the batten-to-batten step up the slope.
- Headlap: the overlap of each row of tiles over the row below.
- Pitch: the slope angle, which sets how much overlap a tile needs.
A worked example from a data sheet
Product sheets state these numbers outright. Wienerberger publishes the Sandtoft Old English Pantile data sheet (version 1.1, dated 02/04/2025) for its clay pantile, and it gives the values in the table below. The sheet words the gauge as "Batten spacing (fixed gauge)".
| Item | Figure |
|---|---|
| Minimum roof pitch | 30° |
| Headlap | 75mm |
| Batten spacing (fixed gauge) | 290mm |
| Weight as laid | 41.6kg per m2 |
A fixed gauge leaves no latitude. Every batten goes at 290mm for that tile, whatever the old roof did. Some products give a range instead of a single figure, and then the sheet states the limits within which the roofer can set the spacing so that the courses finish evenly at the eaves and the ridge. Weight matters here as well, because a heavier covering than the old one can bring Building Regulations approval in at "15 per cent or more", the Planning Portal's wording. These figures belong to that one product, and a different pantile, a concrete interlocking tile or a slate carries different numbers on its own sheet.
Pitch limits sit beside the gauge
A gauge is only valid on a roof that is steep enough for the tile. The minimum pitch changes from product to product. Marley lists 15° for its Lincoln clay pantile and 25° for its concrete Anglia, while Sandtoft's Old English Pantile starts at 30°. Canterbury and Anglia are Marley product names and not places, so a roofer who says Anglia is naming a tile.
Slate has its own limits. Cupa says BS 5534 gives a minimum pitch of 20 degrees for natural slate in a moderate-exposure area for a slate 500mm long with a 115mm overlap, and that "hook fixings should not be used on any pitch below 25º". A slate roof is therefore laid out around its own overlap, and that overlap feeds back into its gauge.
Where a roof is shallow, none of this is optional. A tile used below its minimum pitch, or at the wrong spacing, is outside what the maker designed it for, and the maker's sheet is the only authority on what that means.
Reading and checking the gauge on your roof
You cannot read the gauge from the ground, and the underlay and tiles hide the battens from the loft. It becomes visible when tiles are lifted or taken off, which is why the survey looks at it where a few can be raised, and why the exposed roof of a re-roof is the moment it is set properly.
Ask the firm which tile is going on and what its gauge is, and ask to see the sheet. A tile named only by its look or its colour is not enough, because the same look can come from products with different spacings. The gauge is also one part of a wider specification for your roof, not a standalone number, since fixings and exposure are specified for the site as well. At Total Roofing Great Yarmouth the survey takes in the timber and covering together, and what you get is a single written total with the findings stated plainly.
Our choosing a new roof covering guide compares the options, and the re-roofing process shows where the battens are fixed in the order of work. Both belong to roof replacement.


