Call 01493 277103

Roof replacement

Do Battens Need Replacing on a Re-Roof?

Battens are the timber strips that carry the tiles, and a re-roof is when they can be seen from above. Below is how they are judged, when a new covering needs new ones and what a quote should state.

Get a written quote

Call 01493 277103WhatsApp us

Inside a conservatory with a new solid insulated ceiling and spotlights

The short answer

On a full re-roof the battens are checked as the old covering comes off, and they are replaced where they are rotten, split or set to the wrong gauge. A new tile with its own fixed gauge, such as Sandtoft's 290 mm pantile figure, can mean new battens across the whole roof.

Why a strip shows what a survey cannot

Battens are narrow lengths of timber nailed across the rafters, and the tiles hang from them. From the loft they are partly hidden by the underlay, and from the ground they cannot be seen at all. A full re-roof removes the covering, so for once each batten can be inspected end to end rather than guessed at from a few lifted tiles.

That is the moment to judge them. A batten can look sound and still be split where a nail was driven, soft where damp has sat against it, or marked by old fixings. Underlay and covering are being renewed during the same job, so replacing a doubtful length is simple while the roof is open and a far bigger task once new tiles are down on top of it.

  • Rot and softness: dark timber that gives under a thumbnail.
  • Splits at nail holes, which let a fixing pull out.
  • Old nail holes in a pattern that no longer matches the new spacing.
  • Sag between rafters, which shows as a wave in the roof line.

When a new gauge forces new battens

A tile is made for a particular batten spacing. The maker's data sheet for Sandtoft's clay pantile lists "Batten spacing (fixed gauge)" of 290mm, a headlap of 75mm and a minimum roof pitch of 30°. Laying that pantile means working to the 290mm spacing, with its headlap.

Battens set out for the old tiles reflect the old tile. If the new product has a different gauge, the old timber is in the wrong places and cannot be shuffled along, because the old nail holes would still be in it and the lengths would be crowded. In that case every batten is replaced, even where the timber is sound, because a roof laid to a mixture of spacings would leave some courses with the wrong headlap. A tile whose gauge is not fixed gives the roofer a little room to set the spacing along the slope, within the limits on the product sheet, which is one reason to read that sheet before ordering anything.

The gauge and the batten decision
SituationBattens
New tile has a different gaugeNew timber, set to the new spacing
Same gauge, timber soundReuse can be considered after checking
Rot or splits foundReplace the affected lengths or the lot

Reusing battens: the argument and the risk

Reuse sounds like a saving, and in a few cases it is a fair one. If the old tile and the new tile have the same gauge, and every length has been checked and is sound, there is no technical reason to bin good timber. The word that matters is every. One weak batten can let a fixing pull out, and a tile that slips leaves the underlay exposed.

The saving also has a price in inspection, since every length along a whole slope has to be examined. Reused timber carries the old nail holes too, and a nail driven into a hole that has already been used holds less well.

Marley says that BS 5534 is a code of practice, not law, but since its 2015 amendments mortar alone is no longer relied on to secure the roof covering. Tiles are held by nails and clips driven into the battens, so the timber has to hold a fixing for decades. Good fixings in tired timber are a weak combination.

What a quote should say about battens

A quote that says re-roof and nothing more leaves the battens undecided. Ask whether the price is for new battens or reused ones, and what gauge the chosen tile needs. Ask about the timber too: its size depends on how far apart the rafters are and how heavy the tile is, so a figure copied from another roof is a poor guide, and a firm that has measured yours can say what it will fit. If the figure depends on what the strip finds, ask how a change will be put to you before work goes on.

At Total Roofing Great Yarmouth the survey takes in the timber as well as the covering. Anything it turns up is described in simple terms, alongside one written total price for the roof as it stands.

Our re-roofing process guide shows where the battens come in the order of work, and choosing a new roof covering explains why the tile sets the spacing. Both belong to roof replacement.

Questions and answers

Can new battens be fixed over the old ones?

No. Battens are fixed directly on the underlay over the rafters, so the old ones come off with the old covering. Laying new timber over old would raise the whole roof, bury the original nail holes and alter the eaves and verge details, none of which the covering was designed for.

Can I check the battens myself from the loft?

You can look for damp-stained timber or a sagging line between rafters, and a torch from the hatch is enough. Do not step on the ceiling joists or push through the underlay. Only a lifted tile or a strip shows the timber's real condition, which is why the survey checks it.

Do slate roofs use battens too?

Yes, battens carry slates as well, though the spacing comes from the slate and its overlap, so a slate roof is set out afresh. Where slates are used, the slate supplier's sheet sets the batten spacing, and the same sheet carries the fixing rules, which Cupa words for hook fixings as "should not be used on any pitch below 25º".

Get a written quote

Tell us about your roof

Hand dressing a lead ridge roll with a wooden bossing stick

10-year workmanship guarantee, in writing

Call WhatsApp Written quote