Call 01493 277103

Pitched roofing

Minimum Pitch for Roof Tiles

Every tile design has its own lowest safe slope, set by its maker. Here are the published minimum pitches for pantiles, plain tiles and slate, and where to find the figure that governs your roof.

Get a written quote

Call 01493 277103WhatsApp us

Stacks of new clay plain tiles on scaffold boards beside a battened roof

The short answer

It depends on the product, so the maker's data sheet always decides. Marley lists 15 degrees for its Lincoln clay pantile, 25 degrees for its concrete Anglia and 35 degrees for its concrete Plain tile, while Sandtoft gives its clay Old English Pantile a minimum of 30 degrees with a 75 mm headlap.

Why each tile has its own lowest slope

Tiles shed rain by overlapping, and the overlap works only while water keeps travelling downhill. On a steep slope a shower runs off in seconds. On a shallow one the water crawls, a gust can push it sideways and up under the laps, and a tile that sheds water well at 40 degrees can let it in at 15.

Each maker tests its own profile and publishes a minimum pitch for that one product. The limit is attached to the tile design rather than the material, so two clay tiles with different shapes carry different limits, and so do two concrete ones.

A single number for all roof tiles therefore cannot be right. A roof measured at 22 degrees might suit one concrete tile and be too shallow for another. The dependable check is the sheet for the specific tile named on the quote, read against the slope that was actually measured on your roof.

Marley's published minimums, tile by tile

Marley publishes a minimum pitch for each of its tiles on its page about the minimum pitch for a roof tile or slate. This table repeats the figures in degrees for the clay range and for four of the concrete range.

Marley minimum roof pitch by product
ProductMaterialMinimum pitch
CanterburyClay40 degrees
AshdowneClay35 degrees
HawkinsClay30 degrees
Acme Single CamberClay30 degrees
Lincoln pantileClay15 degrees
PlainConcrete35 degrees
AngliaConcrete25 degrees
Double RomanConcrete22.5 degrees
WessexConcrete15 degrees

The rest of Marley's concrete list runs from 12.5 degrees for Mendip 12.5 and 15 for Mendip, through 17.5 for Edgemere and Modern-Duo, to 22.5 for Ludlow Major, Ludlow Plus and Ashmore. Canterbury and Anglia are entries in Marley's catalogue. Neither describes a place or a style of roof, and a roofer who says Canterbury is naming a product.

Pantiles and slate: two more published figures

Sandtoft, part of Wienerberger, publishes figures for its clay Old English Pantile: a minimum pitch of 30 degrees, a headlap of 75 mm, a fixed batten gauge of 290 mm and 41.6 kg per m2 as laid. They come from its data sheet, version 1.1, dated 02/04/2025. Marley's Lincoln clay pantile is listed at 15 degrees, so two products that both get called pantiles sit 15 degrees apart on paper. The headlap and the pitch are linked, and our page on pantile pitch and headlap sets out how.

For natural slate the source is Cupa, which says BS 5534 indicates a minimum roof pitch of 20 degrees for natural slate on a project in an area with moderate exposure, using a slate 500 mm long with a 115 mm overlap. Cupa adds that no hook fixings should go on a pitch below 25 degrees.

Read the conditions attached to the slate figure: the exposure, the slate length and the overlap are all part of it, and if one of them changes the minimum changes with it. That is the same lesson as the tile table. A pitch figure never floats free of the product, the way it is fixed and the site it is laid on.

What this means when you re-roof

Whatever is laid next has to suit the slope already on the roof. When the tile you like has a higher minimum than your pitch, the choices are a different tile or a change to the structure underneath. A structural change is a matter for building control and a structural check, never a guess from the ground.

Weight sets a second limit. A covering 15 per cent or more heavier than the old one needs Building Regulations approval under the Planning Portal's guide, which suggests asking a structural engineer or surveyor before work begins. It names no material, and neither do we.

Our quote follows a survey that takes in the pitch, the battens, the underlay and the covering, and the figure we give is one written total price. For choosing between coverings, clay against concrete pantiles is a good place to start, and the main pitched roofing page covers the rest. To work out your own slope, see how to measure roof pitch.

Questions and answers

Can I use a tile below its published minimum pitch?

The published figure marks where the maker's evidence stops, and the data sheet outranks any table, this one included. Under it the tile is outside what the maker has stated, so the options are a covering made for that slope or a change to the roof itself. Either route is worked out on the roof after a survey, because a drawing cannot show how the slope really sits.

Do pantiles and plain tiles share a minimum pitch?

No. Marley gives its Lincoln clay pantile 15 degrees and its concrete Anglia 25, while its concrete Plain tile sits at 35. Sandtoft puts its clay Old English Pantile at 30. Pantiles are made from either material, so the word on its own fixes nothing: the named product and its data sheet do.

Who can tell me what my roof's pitch is?

You can measure it yourself, from the loft or from a drawing, and the pitch guide linked above shows how. It is also one of the things we look at on a survey. To have us look first, send a photo on WhatsApp to 07880 284133. A photo from the ground shows the covering and the edges, but only a survey on the roof settles what lies beneath, so the photo opens the conversation while the figure for the slope still comes from the roof.

Get a written quote

Tell us about your roof

Hand dressing a lead ridge roll with a wooden bossing stick

10-year workmanship guarantee, in writing

Call WhatsApp Written quote