The short answer
Measure it from inside the loft: hold a spirit level level against a rafter, measure the vertical rise over a set horizontal run, and convert the ratio to degrees. A phone app laid along the rafter gives the angle directly, and the architect's drawings may state it. Never climb the roof to do it.
What pitch means and the units it comes in
Pitch describes how steeply a roof falls away. Roofing figures quote it as an angle in degrees from the horizontal, so a flat plane is 0 degrees and a vertical wall is 90. Plans and carpenters sometimes use a ratio instead, such as a rise of 300 mm for every 1,000 mm of horizontal run, and the two describe the same slope.
The conversion is simple geometry. Divide the rise by the run to get the ratio, then find the angle whose tangent is that ratio, using a calculator or a phone. A rise of 300 mm over a run of 1,000 mm is a ratio of 0.3, which is about 16.7 degrees. A rise of 700 mm over 1,000 mm is 0.7, or about 35 degrees.
One trap is the word pitch itself. On some drawings it means the rafter pitch, the angle of the timber, and on others it means the roof's overall slope. For a pitched roof with ordinary rafters the two match. Where a roof has a kink, a mansard shape or a curve, each part has its own angle, and the one that matters is the angle of the section being covered. Dormer cheeks, lean-tos and porch roofs carry their own pitch too, so measure each roof you plan to re-cover separately.
Three ways to find it without climbing
Each of these keeps both feet on the ground or on the loft floor:
- In the loft with a spirit level: hold a long level horizontal against the underside of a rafter, measure from the end of the level straight up to the rafter, and read the rise over the length of the level you used. Convert the ratio as above.
- With a phone app: a level or clinometer app, laid flat along a rafter or a purlin, shows the angle directly. Hold it against the timber, not the loose underlay.
- From the drawings: an elevation or section may state the pitch, and if it carries the ridge height and the width of the building, the angle can be worked out from them.
A fourth way, using a photograph, is possible in principle: take it square on to a gable wall, from a distance, and the outline gives the angle. It is rougher than the other methods and works as a check on one of the others.
Why the figure decides the covering
Every tile and slate has a minimum pitch below which its maker does not support it. For pantiles the range is wide: Marley sets its Lincoln clay pantile at 15 degrees and its concrete Anglia at 25, and Sandtoft gives its clay Old English Pantile 30 degrees, with a 75 mm headlap. For natural slate, Cupa says BS 5534 indicates 20 degrees at moderate exposure with a slate 500 mm long and a 115 mm overlap.
A measured pitch of, say, 22 degrees would therefore suit the Lincoln and the Anglia but fall below the Old English Pantile's limit. That is why the figure should come before a choice of covering, not after it. The full table is on our page on minimum pitch for roof tiles, and the interplay with the lap is explained in pantile pitch and headlap.
Pitch also changes how a roof is reached and fixed. A steep slope is harder to stand on, and the fixing specification for the roof takes the pitch into account along with its exposure.
Getting a reliable reading
Measure more than once. Rafters can be out of true, and a slope that has sagged over decades will read differently at the ridge and the eaves. Take readings on both slopes of the roof and at two or three points along each, writing each one down as you go, and use the figure the readings cluster around.
A phone app reads the surface it sits on, so put it on a clean, straight length of timber. If the answer sits close to a manufacturer's minimum, the margin matters, and a survey on the roof is the way to settle it.
At Total Roofing Great Yarmouth we take in the pitch on the survey that comes before a quote for a new covering, and a WhatsApp photo gives us the shape of the roof beforehand. The quote is one written total price. The pitched roofing service covers the work that follows.


