The short answer
Ogee guttering is a gutter whose front face curves in an S-shape, like a classic moulding, with a flat back that sits against the fascia board. It gives a traditional, period look in cast iron, aluminium or plastic. Its capacity depends on the size of the channel, and it needs a straight, sound fascia to sit against.
The ogee profile
An ogee is a curve that bends one way and then back the other, an S-shape, and the name comes from architectural mouldings. On a gutter, that curve is the front face: the channel rises from the base, swells outward and then folds back in towards the top edge. The back of the channel is flat, so the gutter sits snug against the face of the fascia board instead of standing off it as a half-round does.
That shape is why it reads as a moulding on the house, not as a pipe cut in half. Standing in the street, you see a continuous decorative line running along the eaves, which is the reason it is chosen for a house with period character and the reason a plain half-round can look out of place on one.
The same profile is made in more than one material, so the look can be matched to a cast iron original without the weight, or kept to the colour of a modern roofline. A narrow ogee on a small porch or bay roof and a wide one on a long main elevation are both possible, which lets the gutter be sized to the roof it serves.
Capacity: does the shape carry less water?
A gutter's capacity is set by the size of its channel, the number of outlets and the fall along it. The shape matters less than people assume, and a large ogee carries more than a small half-round. Three checks apply to any profile.
- The roof area draining to each outlet, which sets how much water the channel has to take.
- The fall towards the outlet. Brett Martin advises 1mm for every 600mm.
- A clear run, since silt and moss shrink the channel whatever its shape.
Where an ogee is replacing a gutter that overflowed, a size up or an extra outlet is the answer, not a change of profile on its own. The ogee's tall front also holds a little more than a shallow channel of the same width, but the roof area behind it decides whether that is enough. Our guide to gutter replacement cost shows how length and outlets move a price.
Where the existing brackets are spaced widely or have loosened, the full weight of water sits on too few fixings, and a larger channel makes that worse. The maker's spacing for the profile and size is what the new run is set out to.
Materials an ogee comes in
Ogee is made in cast iron, aluminium and plastic. Cast iron is the traditional material and the heaviest, and it is the one to use where a council wants an exact match, as our page on cast iron guttering explains. Aluminium holds the profile in a lighter, painted finish, and plastic is the simplest to fit and keep.
Choosing between aluminium and plastic follows the lines of our guide to uPVC against aluminium guttering. A plastic-roofline retailer quotes 20 to 40 years of reliable performance for correct installation, and that range describes uPVC roofline parts as a group, not ogee in particular. For cast iron and aluminium the condition of the existing gutters, the paint and the fixings is what the survey judges.
MyJobQuote's UK average for a gutter replacement is around £1,000 to £1,600 (20 October 2026). It is not a price for ogee, and the material chosen and the length of the roofline will move the figure.
What an ogee needs behind it
Because the back is flat, an ogee relies on the fascia being flat and true. A board that has bowed, split or sagged leaves gaps behind the gutter and lets the brackets pull away, so the board is checked before the gutter goes up. The fascia is the face board at the eaves, and rot in it shows as soft, dark or flaking timber that a screwdriver sinks into.
Downpipes should match the gutter in finish, and round or square sections are chosen to suit the house, so the whole run looks like one job. Joints and stop ends belong to the same system, and parts from different makers do not always fit each other. A mismatch is noticeable on a plain white wall, where a different curve or finish catches the eye from the pavement.
Our survey looks at the whole roofline, and you receive one written total price. The guttering, soffits and fascias hub shows the other pages on the eaves.


