Call 01493 277103

Guttering, soffits & fascias

What Is Deep Flow Guttering?

Deep flow guttering is a deeper, larger channel than standard half-round. It is made for big roofs, long runs and valleys, but the outlets, the fall and the board behind it need the same attention as the channel.

Get a written quote

Call 01493 277103WhatsApp us

Roofer fitting new anthracite gutter to a uPVC fascia

The short answer

Deep flow guttering is a gutter with a deeper, larger channel than standard half-round, so it holds and carries more water over the same length. It suits large roofs, long runs and valleys that overflow, but it only cures an overflow when the outlets, the fall and the fascia behind it are right as well.

How a deep flow channel differs from half-round

Standard half-round guttering has a shallow, semicircular section. Deep flow keeps a rounded base but the channel is taller and wider, so a length of it holds more water before the flow reaches the front lip and spills. That extra capacity is what helps where a great deal of roof drains to a single point, such as a valley, a long slope or an extension roof feeding the gutter.

A gutter is sized by how much roof drains into it, not by how big the house looks from the road. A long unbroken slope, an extension roof feeding a main roof, or two slopes meeting in a valley all send a concentrated flow to a short stretch of gutter. In a valley, the internal angle where two slopes meet, everything both slopes collect leaves in one stream. If that stream lands in a small half-round channel, it can jump the front edge in heavy rain even though the gutter is clean and sound.

When a standard gutter overflows and deep flow is the answer

An overflow has several possible causes, and only some of them are about size. Look at these before choosing a profile:

  • A choked outlet or downpipe, which no larger channel will cure.
  • Leaves, silt or moss lying in the run and holding water back.
  • A gutter that has sagged between brackets or been set without enough fall.
  • A joint that has opened and lets the flow out sideways.
  • A roof area that simply sends more rain to the gutter than a small channel can carry.

Brett Martin, a guttering maker, advises a downward fall towards the outlet, 1mm for every 600mm. A run set flat or reversed holds water that should be leaving. Where a clean, correctly graded half-round still spills from a valley or a long slope, a deeper channel and an extra outlet are the sensible next step. Our guide to gutter cleaning covers the blockage side of the same problem.

What has to change around the new channel

A deeper gutter carries more water, and water is heavy. The channel hangs from brackets screwed into the fascia board, so that board has to be sound: a soft or split fascia will not hold a bigger, fuller gutter. The fascias and soffits guide explains what the board does and how rot is spotted.

The outlets and downpipes also need looking at, because a larger channel delivering more water to a small outlet only moves the overflow along. The maker's fitting instructions set the bracket spacing and the outlet sizes that suit each profile, and a survey of the whole roofline looks at the board, the brackets, the outlets and the downpipe route together rather than only the length that spilled.

The brackets can fail when a bigger channel goes onto an old fixing pattern. A gutter full of water pulls on every bracket, and a bracket that has loosened in the board will let that length drop at the front. New brackets are set into sound timber at the spacing the maker gives for the profile, and the run is checked again for fall once it is hung.

Material and cost

Deep flow profiles are made in plastic and in aluminium, so the choice between them is the same one set out in our guide to uPVC against aluminium guttering. MyJobQuote gives an average gutter replacement cost in the UK of around £1,000 to £1,600 (20 October 2026). That is a general guttering average, not a deep flow figure, and the length, the number of outlets and the access decide where a given house falls. The written quote is one total price after the survey, and the guttering, soffits and fascias hub covers the rest of the roofline.

Colour and finish are a separate choice from the profile. Deep flow comes in black, white and other shades, and the roofline should read as one job rather than a patch: the new gutter, the fascia behind it and the downpipes are chosen to match each other, and a repair to a single length is matched against the run it joins. A larger channel also stands further out from the board, so it is worth judging the look against the house before the choice is made, not afterwards.

Questions and answers

Will deep flow guttering stop my gutters overflowing?

It will where the overflow comes from too much roof draining into too small a channel. It will not where the cause is a choked outlet, a sagging run or a gutter set without enough fall, because those faults carry straight over to a new gutter. They are looked for at the survey, so the new channel is not asked to hide them.

Does a deep flow gutter need bigger downpipes?

The outlet and downpipe have to suit the channel. The maker's instructions give the matching sizes for each profile, and a long run or a valley may call for a second outlet so the flow has somewhere to go sooner. A big channel delivering to a small outlet only moves the overflow further along the roofline.

Can deep flow guttering be fitted to the fascia I already have?

Only if the board behind it is sound and straight enough to carry a fuller gutter. A fascia that is soft, split or pulling away from the rafter ends is repaired or replaced first, because brackets cannot hold in rotten timber, and a full deep flow channel puts more weight on them than half-round does.

Get a written quote

Tell us about your roof

Hand dressing a lead ridge roll with a wooden bossing stick

10-year workmanship guarantee, in writing

Call WhatsApp Written quote