Call 01493 277103

Flat roofing

Ponding Water on a Flat Roof

Water lying on a flat roof for days is a sign that the surface is not draining as designed. Read on for why ponds form, what the code sets for falls and what a survey does about them.

Get a written quote

Call 01493 277103WhatsApp us

Roofer laying a new mineral felt cap sheet on a flat roof

The short answer

A pond on a flat roof means water cannot reach the outlet. The causes are too little fall, a deck that has dipped, a blocked outlet or a covering built up unevenly. BS 6229:2025 sets a minimum 1:80 finished fall, so a roof holding water has lost or never had that fall, and a survey finds out which.

Why water stays on a flat roof

Despite the name, a roof of this kind is meant to carry a slight slope, so that rainfall drains to a gutter or a rainwater outlet. When a patch of the surface sits lower than the line to that outlet, water gathers in the hollow and stays until the sun and wind dry it off.

Four causes sit behind a pond. The original fall may have been too shallow, so that small dips in the deck were enough to trap water. The deck may have flexed since, because joists have sagged or boards have softened. An outlet or gutter may be blocked with leaves, moss or grit, so even a well-sloped roof backs up. And the covering itself may have been laid unevenly, with thick laps, patches or a second layer building a ridge across the path of the water.

Standing water is not an instant leak, but it keeps the covering wet for long spells, carries dirt that stains and breaks down the surface, and puts weight on a deck that may already be tired.

What the code says about falls

NFRC reports that BS 6229:2025 sets "a minimum 1:80 finished fall for general roof areas and internal gutters". The same standard covers flat roofs with continuously supported flexible waterproof coverings, which means felt, EPDM and GRP and not lead.

The word that matters is finished. A fall of 1:80 means a drop of 1 unit for every 80 units of run once the covering is on, with every tolerance used up. IKO says the code of practice has the roof designed for 1:40 in order to achieve 1:80. A roof designed to the minimum has no allowance left for the deck to settle or for laps to build up.

Our page on flat roof falls goes into how a fall is made, with tapered insulation or firring strips laid to the deck. If the fall on an old roof is below the minimum, repairing the covering leaves the ponds where they are, and a new covering is the chance to put the slope right.

A fall that suits a membrane is different from the pitch needed for tiles, so do not judge a flat roof by the standard of a pitched one. Rainwater has far less slope to run on, which is why a small dip or a thick lap matters so much more.

How a roofer reads a pond

A pond is a symptom, so the survey looks at the cause before it recommends a fix. These are the checks:

  • The outlets, gutters and any scuppers, for blockage or an outlet set higher than the surrounding surface.
  • The deck underfoot, for a spring or dip that points to a sagging joist or a softened board.
  • The covering around the pond, for blistering, cracking, algae or wear where the water sits.
  • The upstands and edges, for water held against a wall by a back-fall.
  • The ceiling below, for stains under the low spot.

A shallow pond that dries within a short spell of rain stopping on an otherwise sound roof may call for clearing an outlet and nothing more. A deep one, or one that never clears, points to a build-up that is out of shape, and the remedy is either re-laying the falls or replacing the covering over a corrected deck.

Getting a ponding roof looked at

Photographs taken just after rain, showing the extent of the water and where the outlet sits, help us see the pattern before the survey. Send them on WhatsApp to 07880 284133, or ring 01493 277103. Do not walk out to the pond to clear it, because a wet, soft surface is slippery and a weakened deck may not take your weight.

The survey takes in the outlets, the deck and the covering together, and any other fault seen while up there is named in the findings. The price then arrives as a written total, whichever remedy the survey points to. Where the covering has little life left, the page on flat roof replacement and the wider flat roofing section show what a new roof involves.

Say in your message whether the pond is in the same place every time it rains, and how long it takes to clear. A pond that moves about, or drains within a day, tells the roofer something different from one that has not shifted for weeks. Mention any ceiling stain below the spot, and whether a gutter or outlet has been cleared recently, because a fresh blockage and a long-standing dip need different repairs.

Questions and answers

Is a puddle on a flat roof a problem?

A shallow puddle that dries out soon after rain is less of a concern than one that lingers for days. Lingering water points to too little slope, a dipped deck or a blocked outlet, and it keeps the covering wet and heavy. The survey decides whether it is a fault in your roof.

Can ponding be fixed without replacing the roof?

Sometimes. A blocked outlet is a simple job, and a low patch can occasionally be built up. If the deck has dipped or the whole fall is too shallow, the covering has to come off so the slope can be corrected, which is why the survey looks beneath the surface as well as at it.

Does the weight of standing water matter?

It can. Water is heavy, and a pond sits on one area of deck for as long as it lasts. On a sound deck that is tolerable, but on boards or joists already softened it adds strain. This is one reason a deck that gives underfoot is looked at before any new covering goes down.

Get a written quote

Tell us about your roof

Hand dressing a lead ridge roll with a wooden bossing stick

10-year workmanship guarantee, in writing

Call WhatsApp Written quote