The short answer
Built-up felt is several bonded layers of bitumen sheet, topped by a cap sheet, forming a flat roof covering. Published lifespans are 10 to 15 years (HomeBuilding) and 10 to 20 years (Less), depending on quality and installation. Felt can be repaired or overlaid where the roof beneath is sound.
Layers, cap sheet and finish
A built-up felt roof is assembled in the order the water would meet it. The first layer goes down onto the deck or the insulation, either nailed through or stuck. One or more further layers are bonded over it, so that the joints of one layer fall away from the joints of the next. A cap sheet goes on top, and on some products it carries a mineral surface of fine granules that shields the bitumen from sunlight.
The layers are joined to each other by heat, by torch, or with cold-applied adhesive, depending on the product. The finished roof is therefore a stack of sheets held together by bitumen, and it behaves as one covering. Where it differs from a single-ply membrane is the number of laps: every edge of every sheet is a joint that has to be closed.
At walls, parapets and penetrations, the felt is turned up and finished with a flashing or trim. The upstand is the most heavily loaded part of the roof, because the sheet has to bend through a right angle where the bitumen resists bending. The commercial flat roofing systems guide compares felt with the other coverings.
Published lifespans
| Source | Figure | Date |
|---|---|---|
| HomeBuilding | 10-15 years | Last updated 30 September 2025 |
| Less | torch-on felt lasts 10 to 20 years depending on quality and installation | Updated 9 November 2026 |
The two sources give different ranges for felt, and neither says what a given roof will do. The wording "depending on quality and installation" is Less's own and it matters: a felt roof laid with care over a sound deck behaves differently from one laid quickly over a damp one. The roof's age is only part of the story, so the survey reads the surface, the laps and the upstands directly. Blistering, split laps, a dried-out cap sheet and open flashings are all things a date on a spreadsheet will not show. Two felt roofs of the same age can be in very different states, because one may have had its outlets kept clear and its walkway protected while the other has stood in water for years. For a roof close to the end of a published range, the question is not whether the age has passed but whether the surface and the layers still hold.
Overlay or strip
When felt wears out, there are two routes. A strip takes off the old layers and relays the roof from the deck up. An overlay leaves the old covering where it is and lays new layers over it, which saves the work and the waste of removal.
An overlay is only sound where the old roof beneath is sound. Wet insulation under tired felt will stay wet beneath a new surface, and blisters in the old layers can show through. The survey checks for both before an overlay is proposed, and where the building control route is not clear it is checked with the council before work starts.
Whichever route is taken, the fall matters. BS 6229:2025 sets a minimum finished fall of 1:80 on membrane flat roofs, and a roof that has settled and ponds will pond again unless the fall is put right as part of the work. A commercial felt roof is priced once the survey is done, and you get one written total for the job.
Our commercial roof surveys guide describes the inspection that makes the decision.
Where felt fails
- Splits along a line of movement, where the roof deck or an expansion joint shifts under the sheet.
- Blisters, where trapped moisture or air has pushed the layers apart.
- Open laps, where a joint between sheets has lifted and rain can run in.
- Worn granules on the cap sheet, which expose bitumen to sunlight and hasten its drying.
- Damage along walkways, from service engineers who cross the roof to reach plant.
- Upstands that have slipped or cracked at the top, behind the flashing.
These faults show from the roof itself, which is why a survey is done up there and not from the ground. Our commercial roof maintenance guide covers keeping outlets and gutters clear between visits, and the commercial roofing hub lists the other guides. Where a roof is walked regularly, a protected route across it takes the wear that would otherwise fall on the felt itself, and the survey notes where one is missing.


