The short answer
Mortar that has receded behind the face of the bricks, joints that crumble to sand, bricks that move, and damp patches on the chimney breast indoors all point to repointing. A survey of the stack confirms it, and the written quote after that survey is one total price for the work.
Marks on the stack itself
Look from the ground in daylight, with binoculars if you have them. Sound joints are full and sit close to the face of the bricks. Worn ones sit back in a groove, so the edge of each brick stands proud and casts a thin line of shadow. In the worst joints the mortar has gone altogether, and you can see a dark gap between one row of bricks (a course) and the next.
Check the gutter, the roof slope below the stack and the ground beneath it. Pale, sandy crumbs of mortar in the gutter or lying on the tiles at the base mean the joints are breaking down and dropping out. Plants rooting in the brickwork, bricks that look tilted or out of line, and white or brown staining running down the faces are further pointers.
Stay off the roof for this. A loose stack can shift under your weight, and what you can see from below is reason enough to ask for a survey.
Signs inside the house
Rain entering open joints wets the brickwork and runs down inside it until it reaches a wall surface. So failing joints can show up lower down, on the chimney breast, which is the part of the wall that encloses the flue in a room. Look for a damp patch, a brown stain, peeling paint or wallpaper, or plaster that has blown, meaning it has lifted away from the wall behind it.
Check the floor above and the loft too, where the brickwork of the stack is bare and easy to see. Damp bricks look darker than dry ones, and a white powdery bloom on the surface is a sign that water has been moving through them.
A damp breast does not prove the joints are the cause. Flashing, the mortar bed holding the pot, a cracked pot and condensation inside the flue can all produce the same patch. Our page on why a chimney leaks sets the causes side by side, and the survey sorts out which one you have.
A quick checklist for the stack
- Joints set back behind the brick face, or missing
- Sandy crumbs of mortar in the gutter or on the tiles
- Bricks that rock, tilt or have slipped out of line
- Moss or plants rooting in the joints
- Damp, staining or blown plaster on the chimney breast
Why open joints matter to the whole stack
A chimney stack stands proud of the roof, so rain and wind reach it from every side. Mortar is the softest part of the structure and is meant to wear before the bricks do. Once the joints are open, water soaks in behind the bricks, and in cold weather the water inside freezes and expands, which loosens the brickwork further. A stack left in that state can start to lean, and a leaning stack needs far more than new joints.
Repointing means raking out the loose mortar and refilling the gaps with fresh mortar. The mix has to suit the bricks and the old mortar around them. A mix that is harder than the original can crack soft bricks, so the survey looks at what the stack is built from before any joint is touched.
Sometimes the joints are only part of the story. If the face of a brick has started to flake, that is a different fault with its own repair, covered in our answer on spalling bricks, and a survey separates one from the other.
What happens once you have spotted them
Before Total Roofing Great Yarmouth gives a price, the roof is surveyed and the whole stack gets checked, not only the joints you rang about. That takes in the mortar bed round the pot (flaunching), the lead where chimney and roof meet, and the pots themselves. If something else turns up, we tell you plainly what it is and what it means.
You can also send a photo on WhatsApp to 07880 284133 for us to look over. A picture from the ground shows recessed joints and loose bricks well enough to judge whether a survey is needed.
What sets the cost is the height of the stack, how it is reached and how many joints have failed, so the figure is fixed in the written quote after the survey. The page on chimney repointing describes the repair itself, and the chimney repairs hub covers every other fault a stack can have.


