Call 01493 277103

Chimney repairs

Chimney Repointing

Repointing renews the mortar between the bricks of a chimney stack. A stack with open joints lets rain into the brickwork, and the wrong mortar can do more harm than the old one. This guide covers the method, the mortar choice and the signs.

Get a written quote

Call 01493 277103WhatsApp us

A stack of new clay plain tiles on a scaffold board

What repointing is, and why a stack needs it

A brick chimney stack is built from bricks held together by mortar. The mortar fills the joints between them and, more than the bricks themselves, it is the part that takes the weather. Rain, frost and sun wear it away from the surface, so that after enough years the joints are hollow, crumbly or missing in places. Repointing is the job of cutting out that worn mortar to a sound depth and filling the joints again with new mortar, so that the stack is closed up and the bricks are held firmly once more.

A stack matters more than a wall at the same height. It rises clear of the roof, so weather reaches every face, and it carries pots, cowls or a cap that add weight at the top. Water that gets into open joints soaks the brick behind, and water that reaches the flue lining can stain the chimney breast inside the house. A stack that is left to decline can reach the point where bricks come loose or the top leans, and that is a rebuild rather than a repoint.

Repointing is a repair to the joints, not to the bricks. If the bricks themselves are flaking or have lost their face, the joints are not the only problem, and new mortar will not cure it. That is why the survey comes first: it tells you whether the stack needs repointing, repointing with some brick replacement, or something bigger.

A stack is also one of several things a roofer looks at in a visit about a leak. Our guide to why a chimney leaks sets out where else water can get in, because failed joints are only one of the possibilities.

Signs the joints have failed

You can see a good deal from the ground. Binoculars or a phone with the zoom turned up will show the state of the mortar on the faces you can reach. Look for joints that have gone back from the face of the brick, so that the brick edges stand proud, and for patches where mortar has dropped out and left a gap. Look at the bricks too: pale powder at the foot of a stack, or flakes lying on the roof below, show that the brick face is breaking up.

A lean is a more serious sign. Hold a straight edge or a plumb line against the stack, or look at the line of the brickwork against the edge of a neighbouring roof, and see whether it appears to tilt. A stack that has moved is not a repointing job until someone has looked at why.

Inside the house, damp on the chimney breast, a brown stain that grows after rain or flaking paint on the wall can come from open joints on the stack, but it can come from other places as well, such as the lead round the base of the stack or a cracked cap. Do not climb up to find out. A survey from the roof takes the guesswork out, and a photo on WhatsApp can start the conversation.

From the ground, look for

  • Joints set back from the brick face, or missing in patches
  • Brick edges standing proud of the mortar
  • Pale powder or brick flakes on the roof below the stack
  • A top that leans, or bricks that have shifted
  • Damp or staining on the chimney breast inside
  • Plants or moss growing in the joints

Raking out: how old joints come out

The first stage is raking out, which means removing the old mortar from the joints to a sound depth. Mortar is cut out by hand or with a small tool, working along each joint and clearing the loose material. The depth matters. A joint that is only brushed over holds a thin skin of new mortar that has little to grip, and a thin skin of mortar falls off. Cutting back to sound mortar gives the new filling something to key into, and filling in layers lets each one set before the next goes on.

Raking out has to be done with care, since the edges of the bricks are what hold the stack together. A tool that is too heavy or a cut that is too deep can chip the bricks, and a stack made of soft old brick is easily damaged. Dust and debris from the work fall inside the stack as well as outside, which is one more reason the flue and pots are looked at as part of the visit.

After raking out, the joints are brushed and cleaned and the brick faces are dampened so that the dry brick does not pull water from the new mortar too quickly. The new mortar is then pressed into the joints in layers and finished to match the profile of the old work. The steps that follow set out the order.

Stacks are worked on from a ladder, a tower or full scaffold, depending on height and where the stack stands. If scaffold would block a footway or the road, the county council issues a highway licence, and we arrange the licence with our scaffolder.

Order of a repoint

  1. Survey the stack, its bricks, its cap and the lead round its base
  2. Rake out loose mortar from every failed joint to a sound depth
  3. Brush out dust and damp the brick faces
  4. Press new mortar into the joints in layers
  5. Finish the joints to match the profile of the sound work

Choosing the mortar: lime, cement and the brick behind

Mortar is not one material. Cement mortar is hard and sets quickly. Lime mortar is softer, takes longer to harden and is more open to moisture moving through it. Mixes between the two exist. The point of choosing is that mortar and brick work as a pair, and the weaker of the two should be the mortar. When water has to leave a wall, it should be able to pass out through the joints rather than the brick face.

Hard cement mortar in a soft old brick reverses that. The joints become less permeable than the brick, so moisture works out through the brick face instead, and the face flakes away while the joints stand proud. That is the damage a wrong repoint can cause, and it is the reason for picking a mortar to suit the brick rather than for convenience. On old brick, a lime-based mortar is what you should expect to be discussed. On newer, harder brick, a different mix may be right.

Colour and finish matter to the look of the house, and a stack with a flush, tidy joint in the right shade sits better on the roof than one with joints picked out in a different colour. But the first test is the strength match, and the finish follows from it.

Where a house is listed, or stands in a conservation area, the choice of mortar can also be a planning matter. Work on a listed home that would affect its character needs listed building consent, and for an Article 4 direction or a conservation area the council is the one to ask. In the Broads, the Broads Authority is the planning authority for land within its executive area. We check with the council before work starts, and our guide to chimney repair costs covers the other routes.

How long new joints last

How long new joints last depends on several things, and a single number would mislead. These are what move the answer. The strength match between mortar and brick has the most to do with it, since a mismatch fails early. The condition of the work comes next: joints raked to a sound depth and filled in layers hold better than joints skimmed over. The exposure of the stack and the state of the cap and flashing complete the picture, because water running onto the joints from a cracked cap or a lifted flashing wears them faster.

That last point is why repointing alone is not always enough. A stack with new joints and a failed flaunching, the mortar bed around the pots, will carry water into the new work. Our chimney flaunching guide covers that part. A stack with a split lead flashing at its base will do the same lower down.

The survey therefore looks at the stack as a whole: the pots, the cap, the joints, the bricks and the lead. The survey findings are given in plain words, with anything else seen on the roof, and what we then give you is a single written total price.

A stack on a thatched house needs a particular word. The fire and rescue services' thatch guide, which covers Norfolk and Suffolk, links many chimney-related thatch fires to heat passing through the flue brickwork into the thatch, and it calls for a qualified chimney sweep. Thatched or not, sound brickwork and joints are part of what a stack on any house should have.

Birds, scaffold and what the quote covers

Before any work, the top of the stack is checked for nests. Wild birds are protected by the Wildlife and Countryside Act 1981: an offence is committed when someone intentionally takes, damages or destroys the nest of any wild bird while that nest is in use or being built. Work around an occupied pot has to wait. A bird guard or cowl is fitted to an empty pot only. If a nest is found, work around that pot waits until the nest is no longer in use.

Repointing is priced after a survey. The sum rests on the number of failed joints, the depth of decay, the state of the brick and the way the stack is reached, so a figure named before anyone has looked is a guess. Where a stack needs scaffold, it sits within the written quote, which is one total price.

To compare quotes from other firms, check that each describes the same job: all four faces or only the worst, raking out to what depth, which mortar, and what happens to the cap and flashing. A photo of the stack can go to us on WhatsApp, 07880 284133, or ring 01493 277103. The rest of what we cover for stacks is on our chimney repairs page.

Questions and answers

What is chimney repointing and why is it necessary?

Repointing means cutting out worn mortar from the joints between the bricks of a stack and filling them again. It is necessary because open joints let rain into the brickwork and the stack, and a stack with failed joints can loosen bricks, stain the chimney breast inside the house and in time need a rebuild.

What mortar should be used on old brick?

Mortar should be no harder than the brick it holds. On old, soft brick a lime-based mortar is what to expect to be discussed, because a hard cement mix can trap moisture and drive the damage into the brick face. The survey and the brick decide the mix, so ask what a quote proposes and why.

Does repointing a chimney need scaffold?

It can. A low stack may be reached by ladder or tower, but a tall stack or one that is awkward to reach can need full scaffold. If scaffold would block a footway or the road, the county council issues a highway licence, and we arrange the licence with our scaffolder, with scaffold sitting inside the written quote.

How do I know if my chimney needs repointing?

Look from the ground with binoculars for joints set back from the brick face, missing mortar, brick edges standing proud, pale powder or flakes below the stack, or a lean. Damp inside on the chimney breast can also point to the stack. Do not climb to check; a survey or a photo sent on WhatsApp is a safer start.

Get a written quote

Tell us about your roof

Hand dressing a lead ridge roll with a wooden bossing stick

10-year workmanship guarantee, in writing

Call WhatsApp Written quote