The mortar bed round the pots
Look at the top of a chimney stack and you will see the pots standing up from a bed of mortar. That bed is the flaunching, and it is worth knowing what it does before deciding what is wrong with it. It is shaped like a shallow cone or a ramp, high against the pot and thinning out to the edge of the stack, so that rain landing on the top of the chimney runs outwards and off, away from the pot and the flue. It also grips the pot, holding it upright against the wind.
The flaunching sits on top of the stack's own structure. Under it is the cap of the stack, the top layer of brick or masonry that closes off the stack between the pots. Beneath that is the brickwork and its joints, which are a separate matter and are covered in our guide to chimney repointing. The flaunching is the weatherproof skin over everything that is hidden under it.
Its job is simple and its position is demanding. It is at the highest point of the house, it takes rain and sun on every surface, and a pot standing in it can rock slightly in the wind, working at the edges. When the mortar fails, there is nothing else between the weather and the cap, and a failed flaunching lets rain into the top of the stack, where it runs down inside the brickwork and can show up as damp on the chimney breast in the house.
In terms of work, it is one of the smaller chimney jobs, but it also tells you something about the stack as a whole, because the parts around it share the same weather.
The top of a stack, named
- FlaunchingSloping mortar bed holding the pot
- PotClay or concrete outlet for the flue
- CowlCover fitted over the top of a pot
- CapTop layer closing the stack between pots
- FluePassage inside the stack for smoke
How a flaunching cracks and fails
Mortar shrinks a little as it dries, and the thin outer edge of a flaunching is where the first hairline cracks form. A hairline crack is easy to overlook from the ground, but it is an opening. Rain enters, soaks the mortar and the cap beneath, and in cold weather water in a crack freezes and widens it. Over time, a crack that began as a hair becomes a gap, and the gap becomes a missing piece.
The pot moves too. A pot stands in the flaunching like a post in a bed of concrete, and when the bond between pot and mortar fails, the pot loosens in the mortar. A loose pot can be felt as a rock in the wind but cannot be felt from the ground, so the clue is a visible gap round the base or a pot that has shifted out of line. A pot that is loose can fall, which is a danger to anyone below.
The mortar itself can be wrong. A mix that is too weak crumbles; one that is too strong cracks away from the brick under it. A flaunching laid too thin at the edge or too flat on top holds water rather than shedding it, and a bed that has no clean edge, or overhang, lets water run back under itself and into the cap.
Plants take hold in cracks as well. Moss and small seedlings growing on the top of a stack show that the mortar is holding moisture and that its surface has opened up.
Signs the flaunching has failed
- Hairline cracks, or gaps round the base of a pot
- Mortar missing from the edge, so the cap shows
- A pot that has tilted or leans out of line
- Moss or plants growing on top of the stack
- Mortar crumbs on the roof or gutter below
- Damp on the chimney breast in the room below
Renewing the flaunching, step by step
A small crack can be raked out and filled, but where the mortar is loose, hollow or crumbling, the better repair is to renew the flaunching. The old mortar is cut away from around each pot, down to the cap, and the pots are checked for cracks, chips and a sound rim. A pot that is cracked, chipped or badly weathered is replaced rather than set back into a new bed, since a bed is only as sound as what it holds.
The pots are then set upright and level on the cap, with fresh mortar packed round the base. The bed is built up against each pot and sloped outwards to the edge of the stack, so that water leaves it quickly, and the edge is finished with a small overhang, which lets rain drop clear of the brick instead of tracking under the mortar. A tidy, sound finish, pressed firmly against the pot with no gaps, is what keeps water out.
The mortar mix matters, as it does elsewhere on a stack. It has to bond to the pot and the cap, flex slightly without cracking and shed water. The right mix depends on what the pots and the cap are made of, and the survey sets it.
The job can be done at the same time as other work at the top of the stack. If the joints below the cap have failed, they are repointed in the same visit, and if the lead round the base has lifted, that is looked at too. Our guide to chimney flashing repair explains that part.
Renewing a flaunching
- Survey the pots, cap and joints beneath
- Cut away loose or hollow flaunching from each pot
- Replace any cracked or badly weathered pot
- Set each pot upright and level on the cap
- Pack fresh mortar round the base and slope it outwards
- Finish with a small overhang at the edge
Pots, cowls and bird guards
Pots come in clay and in concrete, in plain and decorated shapes. A pot lifts the outlet of the flue above the cap, helps the smoke clear the stack and gives the flaunching something to grip. A pot that is cracked from the top down, or that has a broken rim, is replaced, and the flue lining inside it is looked at while the pot is out.
A cowl or cap is fitted on top of a pot to keep rain and birds out. Some cowls let the flue breathe and some close it. If a chimney is not in use, capping it keeps the rain out, but the flue then needs ventilation so that damp air can leave, which is a question for the survey and, where an appliance is involved, for building control. A cowl is only one part of a decision about the flue, and it should be chosen with the stack and the way it is used in mind.
Birds nest in pots. Under the Wildlife and Countryside Act 1981 a person who takes, damages or destroys the nest of any wild bird while that nest is in use or being built, and does so intentionally, commits an offence, so a pot with an active nest is left alone until the nest is finished with. A bird guard is fitted to an empty pot, not to one with a nest in it.
For a stack that serves an open fire or a stove, the flue and pot are matters for the appliance and for building control. And on a thatched home, the fire and rescue services' thatch guide, which covers Norfolk and Suffolk, says spark arrestors, where fitted, "must be kept clean". Thatching is not something we do, and the top of a chimney stack gets the same close look on any roof.
When it is more than flaunching
A flaunching repair is a small job when the stack beneath it is sound. But a failed flaunching is sometimes the visible end of something bigger. If water has been entering the top of the stack for a while, the cap can be cracked or loose, the joints below can be soft, and the brick can be damaged. A stack that leans, or a pot and cap that have moved together, points to a structural problem, and that is a rebuild, not a repair to the mortar.
Damp inside the house is a prompt to look further. Staining on the chimney breast can come from the flaunching, the joints, the lead flashing round the base or condensation in the flue, and a roofer has to separate them. A leak diagnosis has to separate them. The survey looks at the whole stack and the roof around it, from the pots down to the gutters, since a repair at the top that leaves a fault lower down will not stop the damp.
None of this needs a ladder from you. Binoculars from the garden show the state of the top of the stack, and a photo from a phone on zoom is enough to start a conversation. Do not climb to look, and do not lean a ladder on the chimney. A stack can look sound from the garden and still have a hollow bed under the surface, which is why the survey is done from the roof.
Access, scaffold and the quote
Working at the top of a stack is working at height, and the way it is reached decides the price. A low stack can be reached from a roof ladder, a taller one needs a tower or scaffold. Scaffold on the pavement or road needs a highway licence from the county council, and we arrange the licence with our scaffolder, with the scaffold itself sitting inside the written quote.
Flaunching is priced after a survey, as the price depends on how many pots there are, whether any need replacing, how sound the cap and joints are and how the stack is reached. A figure given before anyone has seen the stack is a guess, and a stack with several pots, a cracked cap or awkward access is a bigger job than one pot on a sound cap. Our guide to what chimney repairs cost shows which figures are published and which are not.
A survey takes in the entire roof, so the ridge, the slopes by the stack and the gutters get a look too, and you hear what was seen. The quote that follows is one written total price. Send a photo by WhatsApp on 07880 284133 or ring 01493 277103; the rest of what we cover is on our chimney repairs page.


