Call 01493 277103

Chimney repairs

Damp on a Chimney Breast

Damp showing on a chimney breast can have more than one source. Rain through the stack, condensation inside the flue and salts left in the brick each leave different signs.

Get a written quote

Call 01493 277103WhatsApp us

Roofer re-slating a terrace roof from the scaffold, chimney stacks behind

The short answer

A damp chimney breast comes from rain getting in at the stack, from condensation inside a cold flue, or from salts in the brickwork drawing moisture in. The pattern of the patch helps point to which one, and a survey of the stack and the flue confirms it.

Rain getting in

The stack is the part of the chimney that takes the weather. If rain enters through worn joints, a cracked pot, failed flaunching (the mortar bed round the pot) or the lead flashing at the roof junction, it soaks the brickwork and drains down within it. It then shows on the chimney breast, the part of the wall enclosing the flue in the room.

A patch of rain-driven damp can change with the weather. It may darken after a wet spell, dry out in a dry one, and sit at a point where the water meets a change in the structure, such as the ceiling line or the level of the roof. Brown staining and peeling paint above the fireplace, or a stain on an upstairs breast, point the same way.

Our page on why a chimney leaks goes through the points of entry one by one, and the flashing repair page covers the lead. Fixing the entry point is what stops this kind of damp, and a wall that has been wet for a long time may need drying out before it is redecorated.

Condensation in the flue

A flue that is cold or no longer used can collect moisture from the air inside it. Warm, damp air meeting cold brick condenses, and the wet soaks the inner face of the chimney breast. This is more likely where the flue has been closed off at both ends, so no air moves through and the moisture stays put.

Condensation damp is steadier than rain damp. It may be there in dry weather too, it can come with a musty smell, and it can affect the breast in the room and the brickwork in the loft alike. A flue that is capped and closed off completely is a suspect, which is why the separate answer about capped flues covers the cure in detail. Air that cannot move through the flue leaves the wall wet from the inside, and a cap or board at either end shuts that air in.

If a flue is in use, soot and combustion products can add to the problem, and a flue that is not drawing properly can be damp for that reason. A sweep or an appliance engineer is the person to ask about how a working flue is performing.

Salts in the brickwork

Years of fires leave deposits of soluble salts in the flue lining and the brick around it. Those salts attract moisture from the air, so a breast can feel damp even after the leak has been mended. They show as brown stains that bleed through new paint and plaster, or as a white bloom that comes back when wiped off.

Salts stay in the wall after a leak is fixed, which is why a patch can return when a repair has worked. Staining that comes back, and damp that follows the humidity of the room rather than the rain, are the signs to look for. Replastering over the patch without dealing with the cause can bring the stain straight back.

Telling salts from rain entry matters because the cure differs: one is a repair at the stack and the other is a matter of drying and treating the wall. Treating the wrong one wastes the job, and the stain returns.

Telling the sources apart

Rain entry

  • Worse after wet spells
  • Near the roof line
  • Linked to flashing or joints

Condensation

  • Present in dry weather
  • Musty smell
  • Linked to a sealed flue

What the survey looks at

Because the three sources overlap, the survey takes in everything above the stain and not only the wall itself: the joints, the pots, the flaunching, the lead, the cap if there is one, and the breast as it looks from the loft. Total Roofing Great Yarmouth surveys the roof before giving a price, and anything else seen up there gets reported in plain words.

A photo of the patch sent on WhatsApp to 07880 284133 helps us see the pattern, including whether it sits high or low on the wall. What comes back in writing is one figure covering whatever the survey finds, whether that turns out to be a stack repair, a ventilation fix or both. More on how rain gets in is on the chimney repairs hub, and the flaunching page covers the bed round the pot.

Drying out afterwards takes time, and a wall can stay damp for a while after the cause has been put right. Decorating is better left until it has dried.

Questions and answers

Will a damp chimney breast dry out by itself?

Not while the cause is still there. Rain entry carries on with each wet spell, and condensation continues while the flue stays closed. The wall may look better in dry weather without being cured, and the stain can come back once the weather turns, so waiting for it to clear is not a cure.

Is damp on a chimney breast a problem for the room?

Persistent damp can lead to mould and peeling finishes, and it can spoil furniture placed against the wall. It is worth dealing with for the sake of the room, and the sooner the source is traced the less damage it does to plaster and decoration. A cold, wet breast also makes a room harder to heat.

Can I just paint over the stain?

Paint covers the colour but not the damp, and salt stains bleed through it. The patch should be traced to its source and dried before decorating, or it will come back through the new finish, and fresh paint will blister over a wall that is still wet. Drying comes first, then decorating.

Get a written quote

Tell us about your roof

Hand dressing a lead ridge roll with a wooden bossing stick

10-year workmanship guarantee, in writing

Call WhatsApp Written quote