Call 01493 277103

Blog

Dry Ridge or Mortar: Which Suits a Coastal Roof?

Ridge tiles close the top of the roof where two slopes meet, and they are held on either by mortar or by a dry-fix system. This post covers what the standards say, how each method is built and what to ask about a ridge on the Norfolk coast or inland.

Get a written quote

Call 01493 277103WhatsApp us

Lean-to conservatory with a new solid slate-effect roof Brick house with a new grey tiled conservatory roof

9 min read

What a ridge does and how it is held on

Along the top of a pitched roof, the two slopes meet at a line called the ridge. The tiles on each slope stop short of that line, and a row of ridge tiles caps the gap so that rain cannot run in along the join. Beneath the ridge tiles the underlay and the top batten carry on across the roof, so the ridge is one more layer of cover over a gap that is already shielded from below.

There are two ways of holding those capping tiles down. The older way beds each tile on a ribbon of mortar spread along the top of the slope, with the joints pointed up afterwards. The other way is a dry-fix system, where the tiles sit on a track or batten and are held by clips, brackets or screws, with no mortar bed at all. BS 8612:2018 is the British Standard written for ridge, hip and verge fixing without mortar, and BSI lists it as current.

That standard is why the question in the title is worth asking. The ridge is the highest line on the house, and wind pulls upward on it. So the choice between mortar and dry fix is really a question about how the tiles are held against being lifted, and it is not a question of looks or fashion.

A pantile roof and a plain tile roof both finish at a ridge, and the same two methods apply to each. What changes from house to house is the tile profile, the pitch and the state of the timbers underneath, which is why a roofer looks at the whole roof before saying which method fits.

What the standards say about mortar

BS 5534:2014+A2:2018 is the British Standard covering slating and tiling on pitched roofs, which BSI lists as current. It is guidance on good practice rather than an Act of Parliament, and Marley, the tile maker, puts it plainly: installing to BS 5534 "isn't required by law". Even so, it is the recognised way of doing the work, and a roofer who sets it aside needs a very good reason.

The change worth knowing about dates from 2015. In its explanation of the standard, Marley says the 2015 amendments "made it clear that mortar could no longer be relied upon as the only means of securing the roof covering". Read that sentence for what it says. It concerns mortar being the sole fixing. It does not say that mortar has gone for good, and it does not say every ridge now has to be dry fix. Ridge tiles can still be bedded on mortar, and the standard asks for something extra beside it.

Marley adds a line that applies to ridges and hips directly: "In all cases, ridge or hip tiles should be mechanically fixed to resist the calculated wind uplift force." So the test for any ridge, bedded or dry, is whether each tile is held down mechanically against uplift. A tile that is merely stuck on with mortar fails that test, however neat the pointing looks from the pavement.

Myth

Every ridge now has to be dry fix.

Fact

BS 5534 is not law. Mortar just cannot be the sole means of fixing.

Fixings are chosen for the site, coast or inland

A house near the sea can seem to call for a different ridge from a house in a Broads village or a Norwich street. The way the standard works is more practical than that. Marley states that the minimum figures in BS 5534 "will always be superseded by the generation of a Fixing Specification, which is site specific and takes into account factors such as" location, and the factors it lists include "How exposed is the roof? Local topography". The question is asked of each roof, one at a time.

In other words, the fixing specification allows for the exposure of the site under BS 5534, whether the house stands on the Great Yarmouth seafront, at the edge of the marshes or in a sheltered road inland. The specification belongs to the roof, not to the postcode.

For a homeowner that gives two practical questions. First, ask how the ridge fixings were chosen for your roof and not for roofs in general. Second, ask whether the same thinking has gone into the hips and the verges, which are held by the same logic. BS 8612 covers hip and verge systems as well as ridges, and our page on dry verge systems explains the gable-edge side of the same idea.

Re-bedding, mechanical fixing and dry fix compared

The table sets three approaches side by side as they relate to the standard, using the wording of the two British Standards named above. It describes what each involves, not which one suits your house, because that depends on the roof, the tiles and the fixing specification for the site.

Three ways of holding ridge tiles
ApproachWhat it involvesWhat to ask
Re-bed in mortar onlyOld mortar raked out, tiles re-set in new mortarWhat else holds each tile down?
Re-bed and fix mechanicallyNew mortar bed plus a fixing through or over each tileWhat are the fixings and how many?
Dry-fix systemTiles clipped or screwed to a track, no mortar bedIs the system made to BS 8612?

The first row is the one the 2015 amendments put in doubt, because by itself it leaves mortar as the sole fixing. A roofer who proposes it should be able to say what else secures the tiles. The second and third rows both meet the mechanical fixing test, and the choice between them comes down to the existing roof, the cost and how the ridge finishes at each end. A dry-fix system also changes what the ridge looks like from the street, because the tiles sit on a track instead of a bed, so ask to see a sample of the system before agreeing to it.

Whichever row applies, the ridge is only as sound as the roof it sits on. A ridge repair does not stand apart from the rest of the roof, and the survey has to cover what lies beneath it. If the top batten has rotted or the rafters at the apex have shifted, new ridge tiles on top will not cure that, and it is better to learn this at the survey than after the scaffold is up.

What ridge work costs, from published guides

These are third-party figures, quoted with their dates, and they are not our prices. They span a wide band, because the length of the ridge, the access to it and whether the work is a patch or a full run all change the total. The written quote we give after a survey is one total price for the whole job.

Which? Trusted Traders put a new ridge tile along the top of the roof at £80 to £300, from a survey of 11 Which? Trusted Traders in November 2025, excluding VAT. MyJobQuote gives an average of between £225 and £550 for replacing ridge tiles in 2026, on a page last updated on 1 October 2026, with no VAT basis stated. Checkatrade's repair table, updated in June 2026 and exclusive of VAT, gives ridge tile repairs at £50 to £70 per metre.

Read the per-metre figure as it is printed. It is a rate for a repair, and multiplying it by the length of your ridge would produce a number that the source does not support. A hip gets its price after a survey, and a ridge figure should never be borrowed for one. For the wider picture on pitched roof work, see our guide to what a pitched roof repair costs.

Published ridge figures

New ridge tile (Which?, Nov 2025)£80 to £300
Average ridge tile replacement (MyJobQuote, Oct 2026)average £225 to £550
Ridge tile repairs (Checkatrade, June 2026)£50 to £70 per metre

Which? excludes VAT. Checkatrade's table is exclusive of VAT. MyJobQuote states no VAT basis. Hips are priced after a survey.

What a survey looks at along the ridge

A ridge sits on top of everything else on the roof. Every survey covers the whole roof, and along the ridge that means the line of tiles itself, the state of the mortar if there is any, the fixings, the places where hips and verges meet the ridge, and the batten and underlay beneath.

A check from inside the loft adds what cannot be seen from above, and a survey takes in both. Daylight along the apex, stained timber or a ridge board that has moved are all things that can be seen from the inside and cannot be seen from the pavement.

  • Whether each ridge tile is held by something other than mortar
  • Cracked, hollow or crumbling mortar joints
  • Tiles that have shifted along the line
  • The joins where hips and verges meet the ridge
  • The underlay and top batten beneath the ridge
  • Staining at the apex seen from the loft

Where the ridge needs work, the findings say which of the three approaches in the table the roof calls for. Afterwards we tell you what turned up on the roof, the ridge and the rest, and the written price follows as a single total for the work described. A photo of the ridge sent on WhatsApp gets a look before anything is booked. The full range of roof work is on our pitched roofing page.

How to choose between them

Start with what is on the roof now. A ridge in sound condition, with every tile held by more than mortar, needs inspecting and little else. A ridge with cracked mortar and no other fixing has a different problem, and the repair is a decision about the whole run rather than the loose tile you can see.

Next, ask the roofer to name the fixings and the standard, and to say whether the ridge is a repair or a full replacement along its whole length. A good answer is specific: the type of fixing, the number per tile, and the standard the system or the work follows. A vague answer such as "it is all done properly" is not enough to compare two quotes.

Finally, ask about the ends of the run. Ridges finish at a gable or meet a hip, and the verge tiles and hip tiles have to be dealt with as well, so a quote for the ridge alone may leave part of the same line unaddressed. If one quote covers ridge, hips and verges and another covers the ridge only, the two totals are not comparing like with like. A ridge looks like a small part of a roof, but it runs the full width of the building, and the quote should say how much of that length is being done.

Questions and answers

Is a dry ridge better than a mortar ridge?

Neither wins on every roof. The standard asks that each ridge and hip tile is held down mechanically against wind uplift, and either a dry-fix system or a mortar bed with proper fixings can meet that. Marley's position is that mortar cannot be the sole means of securing the covering, so ask what holds each tile rather than which method has the better name.

Is BS 5534 a legal requirement?

No. Marley says installing to BS 5534 isn't required by law. It is the recognised standard for pitched roof tiling, and BSI lists the 2014+A2:2018 edition as current. A roofer who follows it is working to the accepted method, and one who does not should be able to explain why.

Can one loose mortar-bedded ridge tile be re-set on its own?

A single tile can be re-set, but what holds it needs checking along with the mortar. Cracked or hollow mortar along the line suggests having the whole run looked at rather than patched tile by tile. Our page on re-roofing in clay pantiles shows what the wider job involves when a ridge is part of a bigger repair.

Does a ridge on the coast need different fixings?

The fixings follow a specification worked out for the site, which Marley says weighs the roof's exposure and its local topography, among other things. That applies on the Great Yarmouth coast, on the Broads and inland alike. A roofer should be able to say how the fixings were chosen for your roof, and to put that answer in writing with the quote.

Get a written quote

Tell us about your roof

Hand dressing a lead ridge roll with a wooden bossing stick

10-year workmanship guarantee, in writing

Call WhatsApp Written quote