How a sun tunnel brings daylight down
A sun tunnel has three visible parts and one hidden one. On the roof sits a clear dome, set in a flashing that seals it to the covering. Below the dome a reflective tube runs down through the roof space. At the ceiling, a diffuser, a frosted or prismatic panel, spreads the light into the room. The hidden part is the stretch of tube in the loft, which is where most of the thinking goes.
Light enters the dome and bounces down the inside of the tube. Because the tube is narrow and the surface is mirrored, a sun tunnel lights a space without cutting a large hole in the roof and without a light shaft built by a carpenter. The room gets daylight but no view, since you are looking at a panel, not out of a window.
That is the main difference from a roof window. A roof window opens the room to the sky and, in many models, opens to let air in. A sun tunnel only delivers light. It does not ventilate, it does not provide a way out of a room in an emergency, and it will not make a loft room feel taller. Our page on types of roof window sets the options side by side.
The size is a fixed choice, because tubes come in set diameters. A bigger tube carries more light but needs more clear space in the roof void, and that is the first thing the survey measures. The full range of roof glazing, including the fixed and opening types, is set out on our skylights and roof windows hub.
Sun tunnel parts
- DomeClear cap on the roof that gathers light
- FlashingSheet that seals the dome to the covering
- TubeMirrored duct that carries light to the ceiling
- DiffuserCeiling panel that spreads the light
- CollarRing joining tube sections together
Where a sun tunnel suits a house
A sun tunnel suits the dark space in the middle of a house that no window can reach. An upstairs landing, a hallway under a pitched roof, a bathroom with no outside wall, a walk-in wardrobe or a utility room can all be lit this way. Each has a ceiling that sits close to the underside of the roof, so the tube is short and the light loss is small.
Short and straight is the rule that governs performance. Light is lost each time it hits the tube wall, so a long run or a run with bends delivers less than a direct drop. If the room sits under a ceiling with a deep loft above it, the tube has to cross a long gap and the diffuser will look dimmer. Some systems have a flexible section for sidestepping rafters or a pipe, and each bend should be treated as a cost in light.
The room below matters for another reason. A bathroom produces steam, and a diffuser in a bathroom ceiling sits in the part of the room where that steam collects. A sun tunnel there needs the ceiling around it sealed against the loft so that damp air does not travel up the tube into a cold space.
A sun tunnel is also a reasonable choice where a roof window would be hard to place, for example on a slope that faces the road, on a roof with a chimney stack in the way or over a space too narrow for a window opening.
Rooms that suit a tunnel
- Landings with no outside wall
- Bathrooms and cloakrooms under the roof
- Hallways that run into the middle of the house
- Walk-in wardrobes and dressing areas
- Utility rooms with a short loft above
The tube in the loft
Above the ceiling, the tube crosses the roof void between the diffuser and the roof opening. It has to avoid joists, rafters, purlins, wiring and any water tank or pipework, which is why a loft is checked before a position is chosen. Rafters set the width of the clear space, so a tube that is too wide for the gap needs a rafter trimmed, and cutting structural timber is a matter for the roof's structure and for building control, as our guide to how a roof window is installed explains for the larger opening a window needs.
A cold tube running through a warm house is a condensation risk. Warm room air carries moisture, and where it meets a cold surface it leaves water behind. If the tube passes through loft insulation, the run needs a lagged section so that the tube wall is not the coldest surface in the loft, and the join at the ceiling needs sealing so that room air cannot rise into the void round the tube.
Loft insulation matters on its own account. Approved Document L expects a renovated roof to be improved to the Table 4.3 standard where feasible, and any new opening in the ceiling should not leave a gap in the insulation round the tube. The insulation is laid up to the tube, not stuffed round it, so that it keeps its thickness and the tube remains visible for inspection.
If the loft is boarded for storage, the boards must be lifted at the tube and the area round it kept clear, so that the tube is not crushed by boxes and the seal at the ceiling is not disturbed.
Flashing a sun tunnel into pantile and tile roofs
The dome is only as weatherproof as the flashing under it. A flashing is a sheet of aluminium or lead that sits on the roof covering and rises to the base of the dome. On a flat covering such as slate or plain tile it can be a flat sheet with the surrounding courses dressed over its top edge. On a profiled covering such as a pantile, the flashing has to follow the wave of the tile, because a flat plate leaves a gap beneath each curve.
That is why the type of covering is the first thing checked. Each pantile maker publishes its own pitch limit, and the limits differ by product. Sandtoft publishes 30 degrees as the lowest pitch for its clay Old English Pantile, laid with a 75 mm headlap; Marley's list runs from 15 degrees for the Lincoln, a clay pantile, to 25 degrees for the concrete Anglia. A tunnel flashing is made for a stated range of roof pitch, so the pitch is measured on your own roof instead of guessed.
On a tiled roof, the courses above the dome run down onto the flashing, and the courses beside it overlap the side edges, so water on the slope is led round the dome and not under it. Where the tiles do not sit flat, a profiled filler or a soaker is used to close the gap, and the choice depends on the tile in front of the fitter.
The work involves lifting tiles, so a roof that is already cracked, slipped or brittle needs attention at the same time. A flashing fitted into a tired covering turns every weak tile near it into a future leak.
| Covering | Source | Minimum pitch |
|---|---|---|
| Clay Old English Pantile | Sandtoft | 30 degrees |
| Clay Lincoln pantile | Marley | 15 degrees |
| Concrete Anglia | Marley | 25 degrees |
Condensation and leaks around a sun tunnel
Water in or around a sun tunnel comes from one of two places: the roof or the room. Rain that gets past the flashing runs down the outside of the tube or into the ceiling at the diffuser. Condensation forms inside the tube and drips from the diffuser on a cold, damp day. The two look alike on the ceiling and need different repairs.
A leak shows up after rain, and the stain spreads outwards from the diffuser. Look for cracked or lifted flashing, a dome that has shifted in its collar, mastic that has split or a tile beside the flashing that has slipped. The flashing's upper edge, where the courses above the dome meet it, is a joint worth checking on every visit.
Condensation drips during cold spells and fades once the house warms up. It points to damp room air reaching a cold tube. The fix is on the inside: a better seal at the ceiling, a lagged tube through the loft and better extraction in a bathroom or kitchen. Window faults get the same treatment: work out whether the water comes from outside or in before anything is replaced.
Dust and insects can get into the dome if its seal is poor, and a dome that has crazed or yellowed with age passes less light than a new one. A dome can be replaced without disturbing the flashing, provided the flashing itself is sound. If the tube has been knocked out of line in the loft, light also leaks out at the join, so a dim diffuser is not always the dome's fault.
Rules, checks and the written quote
A sun tunnel is a roof light, so Class C of the General Permitted Development Order is the starting point for a house: it covers roof lights and says no part of the alteration may protrude more than 0.15 metres beyond the plane of the slope of the original roof. On a roof the house was built with, the dome should be checked against that limit; the limit runs from the original roof, so a dome on a later extension is a question for the council, and a flat, a listed home or an address in an Article 4 area changes the answer. The council, or the Broads Authority inside its executive area, is the body to ask.
Building Regulations are a separate question. A sun tunnel is a small opening, but any cut into the roof structure, any change to the ceiling or the insulation and any new electrical work for a light kit can bring in building control or a registered building control approver, so the route is checked before work starts. A tunnel is not an escape route, so a loft room that needs a window for escape cannot rely on one.
The survey does not stop at the future opening, so the covering round the future flashing, the ridge, the verges and the rainwater route all go into what we tell you. A tunnel is a small job, but a flashing fitted next to a broken tile is a failure in waiting.
Our roof window cost page gives a published figure for a Velux roof window, and it is a different product. A sun tunnel's price turns on the covering, the loft and the length of the run, so the figure is one written total that follows the visit to the roof and the loft.


