Call 01493 277103

Skylights & roof windows

Fitting a Roof Window in a Pantile Roof

Pantiles are curved, so a flat flashing cannot seal against them. A roof window fits into a pantile roof once the kit is made for that profile and the tiles are cut round the frame with care.

Get a written quote

Call 01493 277103WhatsApp us

The worn felt roof and cheeks of a box dormer on a chalet bungalow

The short answer

Yes, a roof window can be fitted into a pantile roof, using a flashing kit made for the pantile profile and tiles cut neatly round the frame. A kit for flat plain tiles will not seal against the curve. Check the pitch and the product sheet for your pantile before choosing the window.

Why the profile matters

Each pantile has an S-shaped section, so the roof lies in overlapping waves, with a raised roll along one side of the tile and a hollow along the other. Rain runs in the troughs and down the roof, and the roll of one tile laps over the hollow of the next. The surface is not flat from side to side, so anything sealed against it has to follow the waves.

A roof window flashing kit is the metal that seals the frame to the covering. Kits are made for different coverings, and a kit for a flat or low-profile tile has straight edges that would bridge the troughs of a pantile and leave gaps beneath. A kit for a pantile has a flexible or shaped edge that follows the wave, so rain is carried across the joint rather than into it.

Both clay and concrete pantiles are made, and the two differ in weight, thickness and finish. The kit has to suit the tile actually on your roof, not just the shape, so identify the tile before the window is ordered. Our guide to how a roof window is installed covers the flashing sequence in full.

Cutting and relaying the tiles

Tiles are lifted back round the opening, and the battens between the rafters are cut to make room for the frame. The tiles beside and above are then relaid to the frame edges, and any that meet it are cut so that they sit tight to the flashing. A clean cut keeps the overlap intact and the line of the roof tidy.

  • Lift the tiles round the planned opening and set them aside whole.
  • Cut and trim the battens, and frame the opening in the rafters.
  • Fix the window frame and lap the underlay round it.
  • Add the flashing pieces from the sill upward, each one lapping the one beneath.
  • Relay and cut the tiles to the flashing, keeping the headlap.

Cutting a pantile without cracking it needs a sharp cutting tool and a steady hand, and a tile that has split is replaced instead of reused. Spare tiles are a good idea, because a clay pantile of an older make can be hard to match later. A reclaimed tile of the right type can fill a gap.

Figures from the product sheet

Roof window and tile each have their own limits, and both must be met. On Sandtoft's data sheet (version 1.1, 2 April 2025), its clay Old English Pantile, made by Wienerberger, has a minimum pitch of 30°, a headlap of 75 mm, a fixed batten gauge of 290 mm and 41.6 kg per m² as laid. Marley lists 15° for its Lincoln clay pantile and 25° for its concrete Anglia.

These are separate products with separate limits, which means the numbers that count are on the sheet for your own tile. The batten gauge sets the line of every course, so the cut round the frame has to keep each batten on that gauge, and the headlap has to be kept for the lap to shed water. No single set of numbers covers every pantile.

The roof window's own pitch range is a second check. Makers state the pitches a model suits, so confirm that your slope falls within it. A window designed for a steeper roof can leak if it is fitted to a shallow one, however well the flashing is made.

What to look at before you order

Start by finding out what the covering is. A tile seen from the ground may be clay or concrete, and two similar tiles can be different products, so a close look at one tile or a spare is worth having. If your roof is pantile, the make and the material are what the kit and the pitch limits depend on.

A survey then checks the battens, the underlay and the state of the tiles beside the planned opening. Tiles that are worn, cracked or loose near the frame are replaced while they are open, because they are easier to fix now than later. The skylights and roof windows page lists related jobs.

A new opening in a pantile roof is also an alteration to the roof, so check the planning and building control route first. Roof lights and windows come under Class C in GOV.UK's householder guidance, with conditions, and our guide to Building Regulations for roof windows covers the rest. One written total price follows the survey.

Questions and answers

Can a standard flashing kit be used on pantiles?

A kit made for flat or plain tiles has straight edges that cannot follow the waves of a pantile, so it would leave gaps beneath the metal. Kits are made for pantile profiles, and the right one has to be matched to your covering. Ask for the covering to be named on the kit when it is ordered.

Will cutting pantiles damage the roof?

Cutting a few tiles to fit round a frame is part of normal work and does not harm the rest of the roof, provided the cut tiles sit tight to the flashing and keep their headlap. A tile that cracks in the cut is replaced. Keep any spares from the roof, since a matching tile can be hard to find.

Does a pantile roof need a steeper window pitch?

Two pitches have to be right: the tile's minimum and the window's range. Sandtoft's clay Old English Pantile lists 30° as its minimum, while Marley gives other pantiles lower figures, so the sheet for your tile decides. The window maker's stated range is a separate limit, and both are checked before ordering.

Get a written quote

Tell us about your roof

Hand dressing a lead ridge roll with a wooden bossing stick

10-year workmanship guarantee, in writing

Call WhatsApp Written quote