How a roof window keeps water out
A roof window is a hole in the roof that has been closed up again with several separate layers, and each layer has a different job. The glass sits in a sash, and the sash closes against gaskets in the frame. The frame is fixed to the rafters. Around the frame, a flashing, a set of metal pieces shaped to the roof covering, carries rain from the slope above, past the frame and down onto the slope below. Under the flashing, the underlay is dressed to lead any water that gets that far back out onto the covering.
Inside the room, the other half of the job is done. A lining finishes the opening between the frame and the ceiling, and an insulation collar fills the gap between frame and rafters. Their purpose is not to stop rain but to stop warm air, so that moist room air cannot reach cold parts of the frame and leave water behind.
That split explains why leaks are hard to diagnose. A drip in the room can come from the glazing seals, the flashing, the underlay, the covering above the window or the room's own air. Treating the wrong layer wastes money, which is why the first job is to find which one has failed. Our guide to how a roof window is installed shows each layer in the order it is fitted.
Layers that keep rain out
- Glazing seals between sash and frame
- Frame fixed to the rafters
- Flashing shaped to the roof covering
- Underlay dressed round the frame
- Lining and insulation collar inside
Leak or condensation: reading the signs
Condensation and a leak both leave water around the window, but they behave differently. Condensation forms when warm, damp room air meets cold glass or a cold frame, so it shows on cold mornings and clears as the day warms, with or without rain. A leak depends on the weather outside, so it appears after rain, and heavier or wind-driven rain makes it worse.
Where the water sits is a second clue. Beads on the inside of the glass, a wet cill and mould along the lower lining are the pattern of condensation. Water that streaks down the lining from the top corners, a stain on the ceiling beside the window or drips that start well after the rain has begun point to a leak.
A third pattern is mist between the two panes of glass. That is neither a leak nor room condensation: the sealed unit's edge seal has failed, moisture has got between the panes and the glass cannot be dried from either side. It is a fault with the glass unit and a leak is not involved.
Be careful with a fourth possibility, a leak that is near the window but not from it. A slipped tile, a cracked ridge, a failed valley or a blocked gutter above the window can send water down to the frame, and the stain appears at the window because the frame is the lowest thing in its path. A look at the whole roof around the window comes before any decision about the window itself.
Myth
Any water around a roof window means the flashing has failed.
Fact
Condensation, a failed glass unit or a fault elsewhere on the roof can look identical.
Tracing the water step by step
Start with the pattern, not a tube of sealant. Water inside a house is easy to blame on the nearest opening, and a rushed guess costs more than a careful look. Note whether the water appears after rain, on cold mornings or both. Look at the lining, the ceiling and the cill, and photograph the stain with something in the picture for scale. If you send the photograph on WhatsApp, we can study it before a ladder goes up.
A proper trace works from the top of the window downwards. Water runs along the line of least resistance, so a gap at the head of the flashing can show up as a drip at the bottom corner of the lining. Dry the area, then test sections in turn from the lowest point upwards, so that water cannot arrive from two places at once and confuse the result. That is a job for a ladder and a hose with someone watching from inside, and it takes patience.
Resist two cures that make matters worse. Filling the gap round the frame with mastic stops the drip for a while, then traps water in the joint where it cannot escape and shows the leak again in a different place. Drilling holes to drain a wet lining does the same kind of harm to the frame's own seals.
Last, check the other parts of the roof that water can come from. A hose test only proves a route if it is run for long enough and in the right order, so a quick spray over the whole window proves very little. The courses above the window, the nearest ridge, the verge and the gutter below are all part of the route, and a fault in any of them can end up inside the frame.
Order of checks
- Note when the water appears: rain, cold mornings or both
- Check between the glass panes for mist
- Inspect the lining, cill and ceiling stain
- Look at the covering and gutters above the window
- Test the flashing from the bottom edge upward
Flashing, covering and the kit that fits
A flashing kit is a set of pieces made for one window size and one roof covering. The pieces at the sides lead rain down past the frame, the piece at the top sheds water round it and the piece at the bottom lays water onto the covering below. The set has to match the shape of the tiles, because a pantile, a plain tile and a slate each leave a different gap beneath the flashing that needs to be closed.
A leak at the flashing has one of a few causes. The kit may be the wrong one for the covering, for example a flat kit fitted into a profiled roof. The pieces may have been fitted out of order, so that water is led under a piece, not over it. Lead may have cracked, an aluminium piece may have been bent back or a fixing may have worked loose.
The roof itself is part of the problem when the covering round the window is tired. Checking it takes a few minutes on a ladder and can save a window that would otherwise be condemned. Tiles that are cracked, slipped or lifted can send water past a flashing that is in good order. Slates held by corroded nails slide, and the gap they leave next to the frame is a direct path in.
Replacing a window with the old flashing left in place is a familiar way to get a new window that leaks. A new frame is not necessarily the same size as the old one, and old flashing pieces may be bent, brittle or cut for a different model. Our page on Velux window replacement explains why a replacement is treated as a whole job and not a swap of glass.
Seals, glazing and the lining
The seals are the rubber gaskets that run round the sash and frame. They are a wearing part: rubber hardens, shrinks and splits over time, and a gasket that no longer presses evenly on the sash lets wind-driven rain through at the corners. A frame that has dropped out of square, from an old fitting or a movement in the roof, can have the same effect with new gaskets.
Opening windows add hinges, handles and ventilation flaps, and each is another route. Water can run in beside a hinge cover or through a vent that has been left open in heavy rain. These routes are small, and they look like a flashing fault until the rest has been ruled out.
The glass unit can fail in two ways. A cracked pane is obvious. A failed edge seal is quieter: the gas fill escapes, moisture enters and the glass mists between the panes. Mist that clouds and clears with the weather points to a seal that has gone, and the unit can be replaced without replacing the frame in most window ranges, if the model is still supported.
The lining and insulation round the frame answer the condensation side of the story. If the insulation collar has gaps, or the vapour seal between the lining and the ceiling is broken, warm air reaches the cold frame and condenses there. That is why a window can be sound on the outside and still drip in winter. A replacement window has to meet Approved Document L as well, which accepts 1.4 W/(m²·K) or Window Energy Rating Band B as the floor for a replacement roof window. Ask for the figure on the product label before ordering.
Repair or replace, and what it costs
Repair makes sense when the window is sound and the fault is in a part that can be replaced on its own: a flashing piece, a run of gasket, a tile beside the frame. Replacement makes sense when the frame has rotted, the glass cannot be sourced or the window is too far gone to seal. A window that has leaked for some time can have damp timber round it, so the rafters and lining get checked either way.
On its page last updated 22 September 2026, MyJobQuote gives £1,100 as the average for a mid-range Velux, and says a straightforward swap into an existing opening runs around £100 less. Those figures are for the window, from one source, and they do not show what a leaking one will cost to put right. Our skylights and roof windows hub explains the full range of work.
When we survey a leaking roof window we look at the whole roof around it, not only the frame, because the cause can sit upstream or beside it. We say plainly what we found, including any other fault we spotted on the way. The written quote is then one total price for the work that the survey shows is needed.
If you are not sure where to start, WhatsApp a photo of the window and the stain. It does not take the place of a survey, but it tells us whether the pattern points to condensation, the glass unit or the roof.


