Call 01493 277103

Emergency roof repairs

Flashing Blown Off the Roof

Flashing is the strip of metal or felt that seals a roof against a chimney or wall. Once wind lifts or tears it away, that join is open to rain, however sound the tiles are.

Get a written quote

Call 01493 277103WhatsApp us

Roofer fitting new anthracite gutter to a uPVC fascia

The short answer

Flashing closes the gap between a roof and a chimney, wall or other upstand, so with it lifted or gone, rain gets in along that line. A temporary strip holds for a short while, and lasting repair means new lead or refitted felt. Checkatrade's June 2026 table gives lead flashing repairs at £50 to £70 per metre, excluding VAT.

What flashing does, and what blown-off flashing means

A roof covering seals well across the open slope, where tiles overlap, but it cannot seal against a vertical surface. At a chimney, a party wall, a dormer cheek or a wall that rises above the roof, the join between the two is closed by flashing: a strip tucked into the masonry at one edge and laid over the covering at the other.

Wind gets under the loose end of that strip, bends it back and can peel it clear. Once a flashing is lifted, torn or missing, rain runs straight down the gap and into the structure behind it. The tiles near it can look untouched, and the first you know may be a stain high on the chimney breast, or damp that has appeared on a ceiling close to the stack.

Where the flashing has gone from a chimney, a fallen chimney pot is a related check, because a stack that has lost one piece may have lost another.

Lead and felt, and what a temporary fix does

Lead is the traditional material for flashings, and a lead flashing is dressed to the shape of the joint and held in the masonry joint with wedges and sealant or mortar. According to MyJobQuote, lead flashing that is correctly installed "can last for over 80 years". Lead sheet is graded by code from 3 to 8 under BS EN 12588, and Leadworx, a lead flashing maker, writes: "Code 4 has become the standard choice for general flashing work." The choice for your own roof is set by the details of each junction.

Felt-based flashings are a lighter alternative on some details, particularly flat roofs and simple abutments. Whichever material is on your roof, the repair needs the old flashing, the masonry joint and the covering behind it looked at together.

For a temporary fix, a roofer may fit a self-adhesive flashing strip or a sheet over the open joint to keep rain out. That is a holding measure. Tape does not replace a dressed flashing, and weather can lift it again. Temporary to permanent roof repair sets out how the two stages follow each other.

Dated prices for lead and chimney flashing

All figures here are third-party and dated, and none is our price. Checkatrade, in its June 2026 table, gives lead flashing repairs at £50 to £70 per metre, excluding VAT; that figure is a rate for each metre, and nobody can fairly multiply it into a job price without knowing the length.

For chimney leadwork only, MyJobQuote, on a page last updated 22 September 2026, says: "A chimney lead flashing patch repair typically costs around £200, while a full replacement averages around £570." It adds that a full leadwork replacement costs between £350 and £920, depending largely on whether scaffolding is required. The page's figures apply to chimney leadwork only, and not to valleys, bays or flat roofs.

Our own price is not read off a table. After a survey of the flashing, the chimney and the roof around it, you get one written total. The wider lead hub, lead roofing and leadwork, covers lead flashing, valleys and other detail work.

Getting the joint looked at

Do not climb to look. A chimney flashing sits at the highest, most awkward part of the roof, and a wet slope beside a stack gives little to hold. Here is what you can do from safe ground:

  • Photograph the chimney and the roof beside it from the garden or street.
  • Look indoors for staining high on the chimney breast or on the nearest ceiling.
  • Check the loft by torch from the hatch for dark timber near the stack, staying on the joists.
  • Note when the marks appeared and what the weather was.

With Total Roofing Great Yarmouth the survey takes in the flashing, the stack and the slopes on either side, and anything else that looks wrong gets reported to you in plain terms. Ring 01493 277103, or send your photos to 07880 284133 on WhatsApp. After the survey, the price is given as one written total, so a lifted flashing and a failing mortar joint beside it are quoted together if both need work. Prices on this page come from the dated sources named above, never from us, and the figure for your own roof is fixed only once the survey has been done.

Questions and answers

Can I seal a lifted flashing with silicone or tape?

A bead of sealant or a strip of tape might hold briefly, but neither takes the place of a flashing dressed into the joint, and a wet or windy roof is no place to work. Keep clear of the roof, protect the room inside and have a roofer fit a temporary cover first and a lasting repair after it.

How long can a lead flashing be expected to last?

MyJobQuote says correctly installed lead flashing can last for over 80 years. The wording turns on correct installation, so it describes what well-fitted lead can do and says nothing about the lead already on your roof. The code and fixing depend on the detail, and the survey tells you which suits yours.

Is flashing damage a roof emergency?

It becomes one when rain is coming in at the joint, because that water goes into the wall and the ceiling. A flashing that is loose but not leaking in dry weather leaves room to plan a repair, though the next wind could lift it further. A roofer looking at the joint can tell you which case you have, and whether other flashings nearby are also loose.

Get a written quote

Tell us about your roof

Hand dressing a lead ridge roll with a wooden bossing stick

10-year workmanship guarantee, in writing

Call WhatsApp Written quote