Call 01493 277103

Emergency roof repairs

Making a Roof Safe: Tarpaulins and Temporary Covers

Making a roof safe means keeping the weather out and removing the danger of anything falling, by temporary means until the proper repair. This guide describes each method, what it can and cannot do, and when temporary must become permanent. It sits in our emergency roof repairs pages.

Get a written quote

Call 01493 277103WhatsApp us

Conservatory with a solid ceiling and rooflights opening onto the garden

What making a roof safe actually covers

Making safe is a holding action. It has two aims: to keep water out of the building, and to stop part of the roof injuring anyone or anything below it. It does not repair the fault. A tile that has broken stays broken under a tarpaulin, and a flashing that has torn is still torn beneath a strip of tape. What changes is that the house stops getting wetter and the danger zone stops being open.

Because it is a holding action, the work is shaped by what the damage is and how long the cover has to survive. A broken tile over a dry loft needs far less than a section of roof that a storm has stripped to the battens. Access matters too: a low extension roof can be covered from a ladder, while a steep main roof may need scaffold or a tower before anyone can work on it safely.

Making a roof safe also means looking at what else is at risk. A roofer who is on the roof for one failed ridge tile can see whether the ones either side are loose, whether the flashing at the chimney has lifted and whether the gutter is hanging. That wider look is the start of the survey that the permanent repair needs. The cost of the first visit and the cost of the lasting repair are different matters, covered in our guide to what an emergency roof repair costs.

Sheeting and tarpaulins

A tarpaulin is the best-known temporary cover, and it is easy to put on badly. The idea is to lay a waterproof sheet over the damaged area and carry it up and over the ridge, so rain runs down the outside and cannot get under the edge. The sheet is then fixed down by battens screwed through it into the rafters or the roof timbers, not by bricks or weights, which slide, and not by nails through the tiles, which make fresh holes.

The weak point of every tarpaulin is wind. A sheet with a loose corner flaps, the flapping chafes the fabric and works the fixings loose, and a sheet that has come adrift can slide and take tiles with it. A sheet should reach well beyond the damage on every side, run the full height of the slope it protects and be fixed along each edge. Where a tarpaulin has to run over a ridge, it is fixed on both slopes.

Sheeting suits damage that cannot be mended on the day: a stripped section after a storm, a hole where a chimney stack has come down or a pitched roof opened by a fallen branch. It does not suit a roof that is still unsafe to work on, in which case the first priority is to keep people clear. A tarpaulin is built to last for as long as the temporary period needs, not for the life of a roof, and the sun, the wind and the rain all wear it down.

Temporary cover against permanent repair

Temporary cover

  • Keeps rain out for now
  • Fixed with battens
  • Wears under sun and wind
  • Does not mend the fault

Permanent repair

  • Fixes the cause
  • Matches the covering
  • Priced as one total
  • Follows a survey

Securing loose tiles and ridge tiles

Where the damage is a tile or two that have slipped, lifted or cracked, the job may be one of resecuring rather than sheeting. A slipped tile can be put back into its course and held. A broken tile can be removed and replaced if a matching one is to hand, or the gap can be covered until one is. Ridge tiles that have lifted can be rebedded or held with a temporary fixing, so they stop moving in the wind.

Standards have changed what holds a ridge on. Marley, a tile manufacturer, notes that since the 2015 amendments to BS 5534 mortar "could no longer be relied upon as the only means of securing the roof covering", and BS 8612:2018 sets the specification for dry-fixed systems along ridges, hips and verges. A ridge that is only mortared, and has cracked, may therefore be worth securing mechanically when the lasting repair is done. BS 5534 itself "isn't required by law", as Marley puts it, but it is the code of practice against which tiling is judged.

A temporary re-fixing is judged on what it has to do for a short time: keep the tile from falling, and keep the rain out of the gap. It is not a statement that the covering is sound. If one tile has slipped because its fixing has failed, those next to it may have failed too, and checking is part of the survey. Our page on going from make-safe to permanent repair covers that stage.

Temporary flashing tape and sealing at joints

A flashing is a metal strip, lead for example, that closes the gap between the roof and a chimney, a wall or a roof window. When it lifts or tears, rain runs behind it and into the structure. A temporary fix is to press a self-adhesive flashing tape over the gap, or to apply a sealant, so the water is shed over the top. Both rely on a dry, clean surface, so they suit a roof that has stopped raining and on materials that have dried.

Tape and sealant are stop-gaps. Adhesives age in sunlight and temperature swings, and neither holds the metal in its place the way a properly dressed and fixed flashing does. Lead is the material the lasting repair is made from: MyJobQuote says correctly installed lead flashing "can last for over 80 years", which describes the proper installation, not a taped repair. Leadworx, a lead flashing maker, says code 4 "has become the standard choice for general flashing work", and the survey sets which code the detail needs.

Never climb up to apply tape yourself. The joint around a chimney is an awkward place on the roof to reach, it sits at height and it may be above a wet surface. Describe the leak to a roofer, and do what you can from inside the house with a bucket and a photograph while you wait. The question of who should be on the roof is for the roofer, not the homeowner.

Terms used above

  • TarpaulinA waterproof sheet fixed over damage
  • BattenA timber strip that holds a sheet down
  • UnderlayThe membrane beneath the roof covering
  • FlashingMetal sealing a roof's joint with another surface
  • Ridge tileThe tile capping the top of a slope

Fencing off the danger below

Some of the safety work happens at ground level. If a section of roof could drop tiles, a chimney is leaning or a gutter is hanging, the area below has to be kept clear. The simplest version is a barrier across the path or drive, or a line of tape and cones, with a note for the people who live in or visit the house. If the danger reaches the public pavement, any barrier or scaffold standing there brings the highways rules in as well.

A scaffold is part of the answer on some jobs, since it gives a safe working platform and can carry a protective cover. Scaffolding on the pavement or road needs a highway licence from the county council, and we arrange the licence with our scaffolder. The licence is a legal requirement under the Highways Act 1980, so a scaffold on a public footway is not something to put up first and sort out afterwards.

Inside the house, the equivalent step is to close the door of a room with a bulging ceiling and keep people out. Damp plasterboard is heavy. If water is reaching wiring, lights or sockets, switch the circuit off at the consumer unit only if you can do that without standing in water, and ring an electrician. Our guide on what counts as a roofing emergency helps you decide how urgent your fault is.

Sheet roofs, flat roofs and asbestos cement

Not every roof is tiled. A garage, an outbuilding or an older extension can be covered in profiled sheets or a flat membrane, and each needs different handling when it is damaged. Loose sheets can lift in wind and act like sails. A flat-roof split can be covered with a temporary patch or a sheet until a proper repair is made, and the repair is a membrane job with its own survey.

Older sheeting needs particular caution. HSE gives the rule: "If the building was built or refurbished before 2000, assume that there is asbestos in it." HSE also states that "AC roofs are always fragile", so nobody should walk or crawl on one. Most work on asbestos insulating board is licensed, whereas asbestos cement roof sheets lifted off with care and left unbroken count as non-licensed work, and broken-up asbestos cement is notifiable non-licensed work. HSE lists "AIB white soffit panels to underside of roof eaves" among the places it is found.

If sheets on a garage or shed have cracked or blown loose and the building is of that age, leave them alone. Do not break them, drill them or sweep up the pieces. A roofer will survey first, and the disposal is a separate matter: HSE says "Use a lockable skip for asbestos". Our job is to tell you what we found, not to guess.

Why a make-safe cover is temporary

A temporary cover has a job to do and a limited life. Sheeting moves in wind and wears in sun. Tape ages. A re-fixed tile is only as secure as the batten beneath it. Each of these methods keeps the roof going until the lasting repair, and none carries the promise of one. The longer a temporary cover stays on, the longer rain has to run in at any corner or fixing that is covered poorly.

Next comes a survey covering the entire roof. A surveyor looks at the slopes either side of the damage, the ridge, the verges, the flashings and the gutters, and you hear what else is loose or worn. The lasting repair is then quoted in writing as a single total. From there the finished work, in matching materials, can be planned for dry weather with the access it needs.

Until then, check the cover after every windy night, from the ground. Look for a corner that has come free, a batten that has lifted or water marks that are getting bigger inside. If any of them appear, tell the roofer and send a photo on WhatsApp so we can look at it. You can also read our guide to the move from make-safe to permanent repair.

After the roof has been covered

  1. Check the cover from the ground after wind or heavy rain.
  2. Watch the ceiling and loft for new damp marks.
  3. Photograph anything that changes, with the date.
  4. Book the survey for the permanent repair.

Questions and answers

What does making a roof safe mean?

It means a temporary fix that keeps water out and removes the risk of anything falling, until the lasting repair can be done. That can be a tarpaulin fixed with battens, a loose tile or ridge tile re-secured, flashing tape over a joint, or fencing off the area below. It holds the roof as it is; it does not mend the fault.

How long can a tarpaulin stay on a roof?

A tarpaulin is built to cover a roof for as long as the temporary period needs, not for the life of the roof. Sun and wind wear the fabric and loosen the fixings, so it needs checking from the ground after every windy spell. Get the survey and the permanent repair booked, rather than leaving the sheet to take the weather indefinitely.

Can I put a tarpaulin on my roof myself?

It is not worth the risk. A wet roof is slippery, a sheet in wind can pull a person off balance and the ladder work is hazardous. It is also easy to fix a sheet badly, so it flaps and lets water under. Catch drips inside, keep clear of falling tiles and ring a roofer to cover the roof properly.

Is flashing tape a permanent repair?

No. Flashing tape and sealant hold a joint closed for a limited time and age under sunlight and temperature change. The lasting repair at a chimney, wall or roof window is a flashing dressed and fixed in lead or another suitable metal, with the code set by the survey. Treat tape as a way to get to that repair.

Get a written quote

Tell us about your roof

Hand dressing a lead ridge roll with a wooden bossing stick

10-year workmanship guarantee, in writing

Call WhatsApp Written quote