Call 01493 277103

Roof repairs

What Causes a Sagging Roof?

A roof that dips along the ridge or bows between the walls is carrying something its timbers were not built for. The cause sits in the structure, and the tiles are only the visible part.

Get a written quote

Call 01493 277103WhatsApp us

A bungalow conservatory with a new solid tiled roof

The short answer

A sagging roof comes from the timbers underneath: rafters that have spread, members that are too small or have rotted, a covering that adds weight, or support taken away. Re-tiling cannot cure it. A structural engineer is the right person to say what is failing.

What a sag looks like and where to see it

A sag shows up as a change in a line that should be straight. Stand back from the house and sight along the ridge: a dip in the middle, or a ridge that has dropped at one end, is the clearest sign. A slope that bows inwards between the eaves and the ridge, or tiles that wave in rows when they should lie flat, point the same way.

Inside the loft the evidence can be closer. Rafters that curve instead of running straight, a purlin that has dropped away from the wall, timbers that have pulled out of their joints or gaps opening where the roof meets a gable wall all matter. Take a torch, step only on the joists or on a board laid across them, and photograph what you see rather than prodding it.

Looking is safe, and measuring a roof from a ladder is not. Our page on what a roof inspection covers explains what a survey checks on a pitched roof, and a sag is one of the things that moves a job from tile repair to structural question.

What makes a roof sag

Several causes can act alone or together, and three of them are set out first below. Spread comes first: rafters push outwards at the eaves when nothing ties the feet of opposing rafters together, and the walls or the ceiling joists then take a load they cannot hold. Timber that is too small for its span bends under load, and bends further as the years pass. Timber kept damp by a slow leak, say, can rot and lose strength.

The covering is the fourth. Weight is measured against the covering already there. Under the Planning Portal's guide, a covering "15 per cent or more" heavier needs approval, and Approved Document A treats a change as significant when "the loading upon the roof is increased by more than 15%". The roof was designed for the covering it had, so a heavier one can push a marginal structure past its limit.

Support taken away is the fifth. Removing a chimney breast always needs Building Regulations approval. It is a structural element, not a finish. A roof or purlin that once rested on it needs a new route for its load, and the structural question comes before any tile is touched.

When a structural engineer is needed

A roofer reads tiles, battens, flashings and the condition of the timber that can be seen. A structural engineer calculates loads and designs the remedy. Where a sag is visible, the engineer's view is the one that should set the repair, because the repair might be a strengthened member, a new tie or a change to the support rather than anything done to the covering.

For a heavier covering the Planning Portal is direct: "you are advised to check with a structural engineer or surveyor before commencing with works". We apply the same caution to a roof with a visible dip. Our survey looks across the whole roof, and if it shows a structure that needs an engineer before any covering work, that is what you are told.

  • Ridge or slope visibly out of line: engineer first.
  • A new, heavier covering proposed: engineer or surveyor first.
  • Support removed or planned for removal, such as a chimney breast: engineer and building control first.
  • Rot found in a rafter or purlin: engineer to judge how far it runs.

Cost, safety and what to do now

Structural repair is priced only after a survey and an engineer's advice, because it varies with what has failed. For scale only, two published figures exist. Which? Trusted Traders gave £7,000 to £21,000 for a complete new roof on an average three-bedroom house, excluding VAT (November 2025). Separately, MyJobQuote cites an average of around £650 for a roof repair (6 October 2026). Neither figure covers structural work, so neither should be read as the cost of curing a sag, and a roofer's tile repair does not change what the timbers underneath are carrying.

In the meantime, keep weight off the roof and out of the loft near the dip, do not climb to inspect it, and note whether the dip is changing by photographing it against a fixed line at intervals. Send the pictures on WhatsApp to 07880 284133. Our roof condition reports page covers the written assessment, and the roof repairs hub lists related questions.

Questions and answers

Should I worry if my roof is sagging?

It can be a risk. A visible dip shows that something is carrying more than it was built for, and a weakened timber can move further. Keep weight away from the area and do not stand on the roof or in the loft beneath it. Have a structural engineer look at it, and send us a photograph so we know what the survey will meet.

Can a sagging roof be straightened?

Sometimes the shape can be improved, but that depends on what has caused it. If the timbers have only bowed, strengthening can hold the roof where it is. If a member has rotted, it has to be repaired or replaced. A structural engineer sets out the work, and the covering is then dealt with around it.

Will a heavier covering make a sag worse?

It can add load to a structure that is already stretched. A covering 15 per cent or more heavier needs Building Regulations approval, and the Planning Portal wants a structural engineer or surveyor consulted before work begins. On a roof that already dips, that check is more important, because the extra weight is carried by timbers with little margin.

Get a written quote

Tell us about your roof

Hand dressing a lead ridge roll with a wooden bossing stick

10-year workmanship guarantee, in writing

Call WhatsApp Written quote