Call 01493 277103

Roof repairs

Roof Cleaning Methods Compared

Moss and lichen can be removed in four ways, and they are not equal. This guide compares hand scraping, biocide and soft washing with the jet wash Marley does not recommend, explains why some coverings are fragile, and shows published prices.

Get a written quote

Call 01493 277103WhatsApp us

Torch beam on a wet patch of underlay and rafter in a loft, tracing a leak

Why a roof gets cleaned at all

Moss, lichen and algae settle on a roof where it stays damp, and a pitched roof has plenty of places that do: the shaded slope, the north face, the line of tiles beneath an overhanging branch. Moss holds moisture against the covering and spreads in the overlaps between tiles. Lichen is flatter and grips the surface, and algae shows as dark streaks that spoil the look of a roof without much affecting how it works. Roofs with trees close by, or with slopes that never see direct sun, collect growth fastest, and a roof that holds green growth for years can need more than a surface clean when the work is finally done.

Cleaning is partly appearance and partly upkeep. A roof with moss that is lifting tiles or blocking the lap gaps has a practical problem, while one that has only a green tinge is a question of taste. Either way the method matters, because a roof tile is a fired clay or moulded concrete surface that can be damaged by the wrong treatment, and a damaged surface is harder to keep clean afterwards. Growth that is left can also become a nuisance in the gutters, when pieces break away in rain and travel down to the outlets.

The four methods below differ in cost, in speed and in what they can do to the covering. None of them is a repair. If cleaning reveals cracked tiles, failed pointing or slipped courses, those are separate jobs, and our guide to slipped roof tiles explains what they involve. Our roof repairs page covers the wider picture.

The four methods side by side

Hand scraping uses a scraper and a stiff brush to lift moss and lichen off the surface. It needs no water and no chemicals, and the person doing it can see each tile as they go. It is slow, and it can scratch the surface if the tool is too hard.

A biocide works on the growth itself. It is applied to the surface and left, and the moss, lichen or algae dies back over the following weeks and is then loosened by rain or brushed away. The roof can look no better, or even worse, for a time, because dead growth stays where it is until something shifts it. The method suits a roof where scraping would be slow or where the surface is delicate, and it asks for patience from the owner.

Roof cleaning methods compared
MethodWhat it doesWhat to watch
Hand scrapingLifts moss and lichen with a scraper and brushSlow; can scratch the tile surface
Biocide treatmentChemical applied to kill growth, which then dies backResults appear over weeks, not at once
Soft washingLow-pressure rinse, with or without a treatmentPressure has to stay low
Jet washingHigh-pressure water blasts growth awayMarley does not recommend it

Biocide treatment and soft washing can be used together, with the treatment doing the killing and the low-pressure rinse carrying the debris away. Each product has directions on its label for dilution, drying time and what must be protected, and those directions decide how the work is done, not the roofer's preference. Where plants, ponds or a neighbour's washing are close, the runoff needs thought before the first spray. A quote should name the method and the product, so you know what is going on your roof and can check the label. Soft washing is quicker to see results from than a biocide alone, but it brings water onto the roof, so a roofer will want the overlaps and the underlay sound before using it.

Why Marley does not recommend a jet wash

Marley, the tile maker, is plain about this. Its guidance says: "The use of high powered jet washes is not recommended as it can damage the surface of the slate or tile, thus reducing its expected life considerably". The manufacturer is speaking about its own range, and the warning names both slate and tile.

A tile's surface is part of how it does its job. Concrete tiles have a coloured surface layer and clay tiles a fired face, and the manufacturer's concern is that high pressure damages that surface and shortens the covering's life. A cleaner roof that has lost years of service is a poor trade, which is why the method is worth asking about before the work starts, not after.

That does not make every wash a bad idea. A low-pressure rinse is a different action from a high-powered jet, and a roofer who offers soft washing is describing a gentler method. The distinction to look for in a quote is the pressure and the method named in words, so you are not left to guess from a day rate or a line that says only "clean roof".

If you have already paid for a high-powered wash and the roof now looks patchy, do not repeat it. Have the covering looked at, because damage to the surface is a matter for a survey and not another round of cleaning.

Myth

A pressure washer does no harm when it clears moss from tiles.

Fact

Marley does not advise high powered jet washes; they can reduce a tile's expected life considerably.

Fragile coverings and what not to do on them

Some coverings need extra care whatever the method. Natural slate is cut thin and can crack under a foot or a brush stroke, and old clay pantiles can be brittle. A roofer works from roof ladders or boards that spread weight, and tests the footing before putting weight on a slope. If a tile or slate is already cracked, cleaning it can finish the job. Roof ladders and crawling boards are used for that reason on any covering that might not take a point load, and they stay in place while the work is done.

Fibre cement and asbestos cement sheeting, used on some garages and sheds, is another matter. HSE says: "AC roofs are always fragile", and it advises that you "assume that there is asbestos" in any building built or refurbished before 2000. Do not scrub, scrape or jet such a roof: HSE treats work that breaks up asbestos cement as notifiable, and carefully handled, whole sheets are non-licensed work. Leave it alone and get specialist advice before anyone touches it.

The same caution applies to a roof with a skylight or a glass panel. These can look solid and fail under weight. If the roof has such features, stay off it and let a roofer judge access. Cleaning is not worth a fall, and a clean roof is no use if the person who cleaned it has been hurt.

Roofs that call for extra care

  • Natural slate, which can crack underfoot
  • Old clay pantiles and plain tiles
  • Asbestos cement sheeting on outbuildings
  • Skylights, roof windows and glass panels
  • Any slope with cracked or slipped tiles

Gutters and the ground after a clean

Cleaning sends moss, grit and dead growth down the slope, and the gutter at the bottom catches the lot. A gutter filled with debris backs up, spills over the fascia and wets the eaves timbers, which undoes part of the point of cleaning. Clear the gutters and downpipes once the debris has come off, and check that water runs freely to the outlet.

A gutter is meant to slope gently towards its outlet, and the makers set out a fall for it. A gutter clogged with moss and grit can hold standing water, and a run that has dropped out of line will hold it even when clear. Seeing that after a clean is useful, because it shows a fault the debris had hidden, and a sagging length can be reset without replacing the gutter.

The ground below matters too. Debris from a roof clean can end up on paths, in drains and over plants, and a biocide that is washed off can reach them. Cover drains and plants where the product label says to, and clear what lands on the ground. The work is not finished until the water leaving the roof is leaving it freely. A hose run along the gutter once it is clear will show whether water reaches the downpipe or stops short.

After the roof is cleaned

  1. Clear moss and grit from gutters and outlets.
  2. Check downpipes run freely.
  3. Look for cracked or slipped tiles now visible.
  4. Check gutters still fall towards the outlet.
  5. Clear debris from paths, drains and beds.

What cleaning costs, and when a repair comes first

Checkatrade says: "Roof cleaning in the UK typically costs between £8.50 and £14 per m²", in a guide last updated in April 2026 that states no VAT basis. The rate is for the area cleaned, and it is not a way to price a whole roof by multiplication, because the area, the access and the method all change the job. For an average-sized semi-detached home, the same guide gives a total of £637.50 to £862.50, varying with the cleaning method and treatment. A cheap quote that does not name the method deserves a question, since the same roof can be cleaned gently or harshly for the same headline price.

Gutter clearing is its own cost. Which? Trusted Traders priced emptying every gutter at the front and the back of a house at £75 to £350 in November 2025, excluding VAT. Those figures show scale only. Our roof repair cost guide sets out the published ranges for repairs, and the quote that follows a survey covers the work on your own roof.

Where a repair is needed, it comes before cleaning. Cleaning a roof with cracked tiles or failed flashings can push water under them, and moss that has been holding a slipped tile in place can be the only thing keeping it there. If the survey shows repairs, those are done first, and the clean follows when the roof is sound. That order protects the covering and avoids paying twice for access.

Published cleaning figures

Roof cleaning per m², Checkatrade, April 2026£8.50 to £14 per m²
Average semi-detached total, Checkatrade£637.50 to £862.50
Which? gutter clearing, November 2025gutters: £75 to £350

Checkatrade roof cleaning cost guide, April 2026. Which? Trusted Traders survey, November 2025. Per m² rates are rates, not totals.

Questions and answers

What is the safest way to clean a roof?

For the covering, the gentler methods carry the least risk: hand scraping with a soft tool, a biocide treatment left to work, or a low-pressure soft wash. Marley does not recommend a high powered jet wash for slate or tile, as it says it can shorten the covering's expected life considerably. The person matters too, so leave working at height to a roofer who has the equipment.

Can I jet wash my own roof?

It is a poor idea. Marley's advice is not to use high powered jet washes on slate or tile. Climbing a wet roof with a pressure lance is also an easy way to fall. If a roof is covered in cement sheeting, never jet it: HSE says such roofs are always fragile. Ask a roofer for a gentler method instead.

Do I need to clean the gutters after the roof?

Yes. Moss and grit wash down the slope and into the gutter, where they can block the outlet and make rain spill over the fascia. Clear the gutters and downpipes once the roof is done, and check the run still falls towards the outlet. A clogged gutter can undo the benefit of a clean roof.

Should repairs be done before a roof is cleaned?

Yes, where a survey finds any. Cleaning cracked tiles, failed flashings or slipped courses can disturb them further, and moss can be the only thing holding a loose tile in place. The repair is done first, the roof is cleaned once it is sound, and the written quote comes as a single total for the work described.

Get a written quote

Tell us about your roof

Hand dressing a lead ridge roll with a wooden bossing stick

10-year workmanship guarantee, in writing

Call WhatsApp Written quote