Find where the drip starts before you pay for a fix
Where a conservatory roof drips and where it leaks are different places. Water runs along the underside of a glazing bar, a rafter or a cill before it drops, so a drip over the sofa can start a metre away, at a joint higher up the slope. Mopping up under the drip and sealing above it is a guess. A repair done over the wrong joint leaves the leak where it was and the owner out of pocket.
The sound approach starts on the outside and works inward. The roof is inspected from the top, along every glazing bar, every sheet or pane edge, the ridge, the eaves and the junction with the house wall. Inside, the rafters and the frame are checked for stains, soft or darkened timber, rust at fixings and white tide marks on the plaster, which show where moisture has been moving.
A hose test shows the route. Water is run onto one section of the roof at a time, starting low and working up, while someone inside watches for the first drip. The low-to-high order matters: if the water started at the top, every joint below it would be wet and the test would prove nothing. A test that finds nothing in dry weather is also information, because it can mean the leak needs wind-driven rain or on heavy flow that a hose does not copy.
This guide takes the places a conservatory roof can fail in the order the water meets them. If the roof is old and the problem is wider than one joint, the conservatory roofs hub sets out the replacement options.
Glazing bars, caps and the seals under them
A glazed conservatory roof is built from sheets or panes held between glazing bars, which are the long aluminium or uPVC sections that run from the ridge to the eaves. Each bar has a base that carries the glazing and a cap screwed or clipped on top. A rubber or foam gasket sits between the cap and the glass or the sheet, and that gasket is what keeps rain out of the joint.
Gaskets wear. Sun, heat and cold make rubber harden, shrink and pull away from the edge of the glazing, and a gap of a millimetre or two is enough for rain to run in under the cap, along the sheet's edge and down into the room. Caps can also work loose when the screws under them back out or the bar moves with the heat of the day. A cap that lifts by even a little leaves a path for wind-driven rain.
Repairs at this level include replacing the gasket, re-seating the cap with new fixings and resealing the ends of the bars. They are sound repairs where the bars are straight and the glazing is undamaged. They are poor value where the gaskets have failed along the full length of the roof, because the next failure is close behind the last and the bars themselves are the same age as the gaskets.
A glazing bar can also leak at its lower end, where it meets the eaves beam or the gutter. The end cap and the seal there take the full flow of water from the bar above them, so a gap at the eaves shows up in the room as a drip along the head of the window below.
Signs a glazing bar is the leak
- A cap that lifts or rattles when pressed
- A rubber gasket that is hard, cracked or shrunk
- A stain that runs down in line with one bar
- A drip at the eaves end of a bar
- Daylight visible along the edge of a sheet
Polycarbonate sheets and glass units
Polycarbonate sheets are made with hollow channels running down their length, and each end of every channel has to be closed or taped. If the closure at the top is missing or has come off, water and dirt get into the channels, and green growth shows inside the sheet. If the closure at the bottom is blocked, the water that gets in cannot run out. A sheet that has gone green inside is a sheet with a failed end seal, and a clean will not remove that.
Polycarbonate can also crack where fixings were over-tightened or where the sheet has moved with temperature. A crack lets rain straight through, and a crack near an edge spreads. A sheet that is cracked, yellowed or brittle is a sheet at the end of its life. HomeBuilding gives polycarbonate roofs a lifespan of 10 years: "They have a typical lifespan of 10 years." That figure is HomeBuilding's own, and a roof older than that is already past it.
Glass roofs leak differently. A pane of sealed double glazing that has failed its edge seal fills with moisture between the two sheets, and misted panes are a failure of the unit, not of the roof around it. The unit lets in no rain, but it does lose its insulating value, and the mist is permanent. A cracked or chipped pane lets rain in, and a replacement unit is made to the size of the opening, so the pane's exact measurement matters.
Roofing Megastore's managing director, quoted by HomeBuilding, says: "A glass conservatory roof will likely last in excess of 30 years." That is one trader's view, and a glass roof's frame and gaskets age at their own rate. Where the glass is sound but the joints leak, new gaskets can be the answer.
The box gutter, valleys and the ridge
Some conservatory roofs have a gutter built into the roof itself, at the line where two slopes meet or where a roof meets a wall. A box gutter is a channel set into the structure, lined with a membrane or lead, and carries water to an outlet. If its outlet blocks with leaves or moss, the channel fills and overflows, and the overflow runs inside the building, not outside.
A gutter built into a roof is a different kind of problem from one on the outside. It cannot simply be swung down and cleaned, because it is part of the roof. Its lining is also one continuous layer that must hold water at a depth, so a split, a lifted seam or a failed joint leaks wherever it is. The fall toward the outlet has to be right, because a channel that holds a standing pool wears faster at the pool. Brett Martin's figure for the fall on guttering is 1 mm for every 600 mm towards the outlet, for ordinary external gutters.
The ridge is the line along the top, where the two sides of a roof meet. A ridge on a glazed conservatory is capped with a trim that is sealed along each side, and the seal can fail like any other. On a solid conservatory roof the ridge is covered with ridge tiles or a ridge system, and Marley's wording on the standards for ridge and hip tiles is that they should be mechanically fixed to resist the calculated wind uplift force. A loose or cracked ridge tile can let rain into the roof's top edge.
Hips, valleys and the places where a gable roof meets a hipped one each need their own detail, and each is a place to look when a stain appears in a roof's corner and not along its slope.
The wall junction and the flashing
At the house wall, the join has to shed water down the roof and keep it out of the masonry. This is done with a flashing: a strip of metal such as lead, dressed up the wall and over the roof covering. The top edge of the flashing goes into a groove cut into the brickwork, called a chase, and is sealed with mortar or sealant. The lower edge lies over the roof so that water runs down the roof and not behind it.
A flashing leaks when its top edge comes out of the chase, when the sealant has failed, when the lead has split or lifted, or when the mortar has cracked. Rain then runs behind the lead and down the inside face of the wall into the conservatory. A stain high on the house wall, inside the room, is the sign to look for. A glazed roof can have a cover strip sealed with silicone at this join instead, and that seal ages like any other.
MyJobQuote says correctly installed lead flashing can last for over 80 years. That is for flashing that is correctly installed and still in place. Leadworx, a lead flashing maker, says code 4 has become the standard choice for general flashing work, and the written specification sets the code for every detail. A flashing that has failed within a decade has been poorly fitted or has moved, because lead that is fitted correctly does not wear out that fast.
If the conservatory abuts a neighbour's wall, a new flashing that has to be cut into that wall is work to a party wall, and the Party Wall etc. Act 1996 treats cutting into a wall of the adjoining owner's building to insert a flashing as work that needs a notice. The building owner issues it: at least two months ahead, with a surveyor needed only if the neighbour dissents or does not reply within 14 days.
Patch the roof or renew it
A repair fits when the defect is confined to one place and the remaining roof is sound. A single lifted cap, one failed gasket section, a blocked box gutter outlet or a loose ridge section are repairs. They address a cause that can be named, at a place that can be reached, and the roof around them is in a condition to keep doing its job.
A repair stops being the right answer when the leak is a symptom of the roof's age. If the gaskets have hardened along the whole roof, the polycarbonate has gone brittle and green, the bars are corroded or the sheets move in their seats, patching one joint moves the leak to the next one. A roof in that state has a repair bill that grows and a room that never dries out.
The other consideration is what the room is used for. A conservatory that doubles as a dining room, an office or a playroom cannot tolerate a leaking roof as a storage shed might, and a roof that cannot be relied on in heavy rain is a reason to look at replacement. The guide to lightweight warm roofs and the comparison of glass and polycarbonate roofs cover the options for a new covering, and the cost guide covers what replacement costs in published figures.
Whichever route, our survey looks over the whole roof and the structure beneath it, and anything else spotted beside the leak is described to you. The written quote then gives one total price, whether the answer is a repair or a new roof.
How a leak is traced
- Inspect the roof from outside along every bar, edge and junction
- Check inside for stains, soft timber and rusting fixings
- Test one section at a time with water, low to high
- Name the cause and where it sits
- Decide between a local repair and a new roof


